Results 41 to 50 of about 51,955 (285)
RECYCLING AND PROPERTIES OF RECYCLED ALUMINIUM ALLOYS USED IN THE TRANSPORTATION INDUSTRY [PDF]
Transport Problems, 2016 Nowadays, a transportation industry creates a lot of metal scrap because production and use of cars are on the increase worldwide. This is based on the fact that increase in the production of cars increases usage of aluminium alloys in transportation ...
Lenka KUCHARIKOVÁ +2 more
doaj +1 more source
Effect of Al addition on microstructure of AZ91D [PDF]
, 2014 Casting is a net shape or near net shape forming process so work-hardening will not be applicable for improving properties of magnesium cast alloys.
Joshi, U +3 more
core +1 more source
Micromechanisms of short fatigue crack growth in an Al-Si piston alloy [PDF]
, 2014 The short fatigue crack growth behaviour of a model cast aluminium piston alloy has been investigated. This has been achieved using a combination of fatigue crack replication methods at various intervals during fatigue testing and post-mortem analysis of
T.O. Mbuya +3 more
core +1 more source
Fatigue crack growth behaviour and life prediction for 2324-T39 and 7050-T7451 aluminium alloys under truncated load spectra [PDF]
, 2010 This paper presents a study of crack growth behaviour in aluminium alloys 2324- T39 and 7050-T7451 subjected to flight-by-flight load spectra at different low- stress truncation levels. Crack branching was observed in the higher truncation levels for the
Bao, Rui, Zhang, Xiang
core +1 more source
On the correlation between roping, texture, and morphology of aluminium alloy sheets
Journal of Materials Research and Technology, 2023 Roping is a troublesome surface defect of aluminium alloy sheets that hinders their application in the automobile industry. When the aluminium alloy sheets are subjected to tension, the texture components of various distributions will lead to non-uniform
Yuanzhe Hu +7 more
doaj +1 more source
A-242 Aluminium Alloy Foams Manufacture from the Recycling of Beverage Cans
Metals, 2019 This paper presents and discusses a methodology implemented to study the process of the preparation of aluminium alloy foams using the alloy A-242, beginning from the recycling of secondary aluminium obtained from beverage cans. The foams are prepared by
Nallely Montserrat Trejo Rivera +2 more
doaj +1 more source
Buildings, 2023 Recently, new types of C-shaped members made from AA-6086 and 7075-T6 high-strength aluminium alloy have become more popular due to their high yield strength and lower cost.
Xiaoyong Sun, Jianhang Fu, Gang Sun
doaj +1 more source
Laser Powder Bed Fusion of Alumina: Effects of Scanning Strategies on External and Internal Defects
Advanced Engineering Materials, EarlyView.This study investigates how scanning strategies affect pure alumina in laser powder bed fusion. Linear 45° scanning yields uniform surfaces but high porosity, while the island‐concentric strategy provides higher density with through‐holes favorable for infiltration. Findings highlight pathways toward optimizing defect‐free alumina parts.
Mohamed Abdelmoula +7 more
wiley +1 more source
Surface characterization and influence of anodizing process on fatigue life of Al 7050 alloy [PDF]
, 2011 The present study investigates the influence of anodizing process on fatigue life of aluminium alloy 7050-T7451 by performing axial fatigue tests at stress ratio ‘R’ of 0.1.
Chaussumier, Michel +9 more
core +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source