Results 61 to 70 of about 51,955 (285)

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

The Effect of Laser Surface Treatment on Structure and Mechanical Properties Aluminium Alloy ENAC-AlMg9

Archives of Metallurgy and Materials, 2016
In this work, the influence of a high power diode laser surface treatment on the structure and properties of aluminium alloy has been determined. The aim of this study was to improve the mechanical and tribological properties of the surface layer of the ...
Pakieła W., Dobrzański L.A., Labisz K., Tański T., Basa K., Roszak M.   +5 more
doaj   +1 more source

Enhancing Strength and Electrical Conductivity in Al–Zr–Sc Conductor Alloys Through Sn and Sr Microalloying and Two‐Step Aging Treatment

Advanced Engineering Materials, EarlyView.
Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao, Emad M. Elgallad, Alexandre Maltais, X.‐Grant Chen   +3 more
wiley   +1 more source

Black anodic coatings for space applications: study of the process parameters, characteristics and mechanical properties [PDF]

, 2009
Black inorganic anodized aluminium alloys are used for managing passive thermal control on spacecraft and for avoiding stray light in optical equipment.
Tonon, Claire, Arurault, Laurent, Goueffon, Yann, Mabru, Catherine, Guigue, Pascale   +4 more
core   +1 more source

Research of Preliminary Plastic Deformation Value Influence on Artificial Ageing Dynamics

Mokslas: Lietuvos Ateitis, 2014
Product quality improvement in the machine manufacturing industryis tightly associated with the introduction of new materialsand technologies. Aluminium alloys are widely used in differentmachine production industries.
E. Chumakov, S. Shukbarova, Irmantas Gadzevičius, Justinas Gargasas   +3 more
doaj   +1 more source

Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland, Finn‐Lennard Janthur, Sarah Seffer, Jörg Hermsdorf, Ludger Overmeyer, Annika Raatz   +5 more
wiley   +1 more source

Combined Process‐ and Phase‐Field‐Simulation to Predict the Microstructure of Single‐Crystal Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm, André B. Baldissera, Rainer Völkl, Uwe Glatzel   +3 more
wiley   +1 more source

Direct selective laser sintering of aluminium alloy powders [PDF]

, 2008
The SLS/SLM of aluminium powder had been investigated by studying the effect of powder properties and laser processing parameters on the microstructures and properties of both single layer and multiple layer builds. On the basis of experimental evidence,
Olakanmi, Eyitayo Olatunde
core  

Grain refinement in a AlZnMgCuTi alloy by intensive melt shearing: A multi-step nucleation mechanism

, 2011
This is a post-print version of the article. Copyright @ 2010 Elsevier B.V.Direct chill (DC) cast ingots of wrought Al alloys conventionally require the deliberate addition of a grain refiner to provide a uniform as-cast microstructure for the ...
Jarry, P, Li, HT, Scamans, GM, G.M. Scamans, Xia, M, H.T. Li, M. Xia, Z. Fan, Fan, Z, Ph. Jarry   +9 more
core   +1 more source

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source