Results 81 to 90 of about 51,955 (285)
A super-ductile alloy for the die-casting of aluminium automotive body structural components [PDF]
, 2014 Super-ductile die-cast aluminium alloys are critical to future light-weighting of automotive body structures. This paper introduces a die-cast aluminium alloy that can satisfy the requirements of these applications.
Ji, S, Watson, D, Fan, Z
core +1 more source
Assessing Altered Coating Adhesion on Plasma‐Deoxidized Surfaces Under Oxygen‐Free Conditions
Advanced Engineering Materials, EarlyView.This study demonstrates the effectiveness of atmospheric pressure plasma pretreatment in modifying silicon and stainless steel surfaces to improve adhesion. Argon‐hydrogen plasma increases surface roughness and improves adhesion strength, whereas pure argon results in smoother surfaces and structural changes.
Selina Raumel +6 more
wiley +1 more source
Potential fatigue strength improvement of AA 5083-H111 notched parts by wire brush hammering: Experimental analysis and numerical simulation [PDF]
, 2014 The effects of milling as machining process and a post-machining treatment by wire-brush hammering, on the near surface layer characteristics of AA 5083-H111 were investigated.
SIDHOM, Habib +4 more
core +1 more source
Advanced Engineering Materials, EarlyView.The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu +8 more
wiley +1 more source
Effect of sealed anodic film on fatigue performance of 2214-T6 aluminium alloy [PDF]
, 2012 The aim of present study is to investigate the influence of anodic film, grown by sulfuric acid anodizing and sealed in nickel-acetate solution, on fatigue strength of aluminum alloy 2214-T6 by conducting axial fatigue tests at stress ratio ‘R’ of 0.1 ...
Chaussumier, Michel +9 more
core +1 more source
Elimination of cracks in Al–Zn–Mg–Cu alloy by addition of TiO2 in selective laser melting
Journal of Materials Research and Technology7050 aluminium alloy is widely used in aerospace industry due to its excellent mechanical properties. 7050 aluminium alloy belongs to Al–Zn–Mg–Cu alloy.
Biao Huang +7 more
doaj +1 more source
Evaluating Energy Absorption Performance of Filled Lattice Structures
Advanced Engineering Materials, EarlyView.Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney +2 more
wiley +1 more source
Chemical Engineering Transactions, 2018 Aluminium alloys are widely used in various industries because of their lightness and easy processing, leading to higher requirements for aluminium alloys in terms of the flatness and finish of aluminium alloy surface.
Yali Zhao +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht +5 more
wiley +1 more source
Macrosegregation in direct-chill casting of aluminium alloys [PDF]
, 2008 This is the post-print version of the final paper published in Progress in Materials Science. The published article is available from the link below. Changes resulting from the publishing process, such as peer review, editing, corrections, structural ...
Nadella, R +7 more
core +1 more source