Results 71 to 80 of about 131,838 (287)
Research of Preliminary Plastic Deformation Value Influence on Artificial Ageing Dynamics
Mokslas: Lietuvos Ateitis, 2014 Product quality improvement in the machine manufacturing industryis tightly associated with the introduction of new materialsand technologies. Aluminium alloys are widely used in differentmachine production industries.
E. Chumakov +3 more
doaj +1 more source
Zaštita Materijala, 2022 The effect of applied magnetic fields on the corrosion of aluminium alloys AA3003 and AA8011 in hydrochloric acid solutions at room temperature has been investigated by using the gravimetric technique.
Igweze Daniel Chukwuebuka +1 more
doaj +1 more source
A predictive fatigue life model for anodized 7050 aluminium alloy [PDF]
, 2013 The objective of this study is to predict fatigue life of anodized 7050 aluminum alloy specimens. In the case of anodized 7050-T7451 alloy, fractographic observations of fatigue tested specimens showed that pickling pits were the predominant sites for ...
Chaussumier, Michel +4 more
core +4 more sources
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Effect of frictional boundary conditions and percentage area reduction on the extrusion pressure of Aluminum AA6063 alloy using FE analysis modelling [PDF]
, 2020 © 2020 by the authors; licensee Growing Science, Canada. This is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC-BY) license (http://creativecommons.org/licenses/by/4.0/).Finite Element Analysis ...
Ismail, Sikiru O. +2 more
core +2 more sources
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Experimental validity on the casting characteristics of stir cast aluminium composites
Journal of Materials Research and Technology, 2020 In the present work efforts are made to confirm the presence of actual weight percentage of reinforcements and its effect on aluminium alloy composites during stir casting technique. Two types of reinforcements, such as Silicon carbide and Boron carbide,
Gowrishankar M C +4 more
doaj +1 more source
Microstructural characteristics of diecast AlMgSiMn alloy [PDF]
, 2014 Solidification and microstructural characteristics of Al-5wt.%Mg-1.5wt.%Si-0.6wt.%Mn- 0.2wt.%Ti alloy have been investigated in high pressure die casting. The average size of dendrites and fragmented dendrites of the primary α-Al phase formed in the shot
Fan, ZY, Ji, SX, Wang, Y, Watson, D
core +1 more source
Advanced Engineering Materials, EarlyView.Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao +3 more
wiley +1 more source
Research of preliminary plastic deformation value influence on artificial ageing dynamics
Mokslas: Lietuvos Ateitis, 2013 Product quality improvement in the machine manufacturing industryis tightly associated with the introduction of new materialsand technologies. Aluminium alloys are widely used in differentmachine production industries.
E. Chumakov +3 more
doaj +1 more source