Results 51 to 60 of about 600,875 (267)
On the correlation between roping, texture, and morphology of aluminium alloy sheets
Roping is a troublesome surface defect of aluminium alloy sheets that hinders their application in the automobile industry. When the aluminium alloy sheets are subjected to tension, the texture components of various distributions will lead to non-uniform
Yuanzhe Hu +7 more
doaj +1 more source
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt +8 more
wiley +1 more source
Copper‐based composites enhanced with carbon feature convenient mechanical properties and favorable electric conductivity. Processing via deformation and thermomechanical treatments can introduce advantageous microstructures further enhancing their performance. Herein, copper–graphene powder‐based composites are directly consolidated via rotary swaging
Radim Kocich +3 more
wiley +1 more source
The inhibition effect of mad Honey on corrosion of 2007-type aluminium alloy in 3.5% NaCl solution [PDF]
The inhibition effect of mad honey on corrosion of 2007-type aluminium alloy in 3.5% NaCl solution was investigated by Tafel extrapolarisation (TP), electrochemical impedance spectroscopy (EIS) and dynamic electrochemical impedance spectroscopy (DEIS ...
Husnu Gerengi +2 more
doaj +2 more sources
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
Effects of Mg on Microstructure and Solidification of a Hypereutectic Zn–8 wt.%Al Alloy
An appreciable set of results involving thermal data, microstructure, chemical composition, and microstructural growth laws is reported for ZnAlMg alloys. Such results demonstrate that ZnAlMg alloys have high potential for applications in automotive self‐lubricating components, batteries, and electrical systems.
Raí B. de Sousa +6 more
wiley +1 more source
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe +6 more
wiley +1 more source
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin +12 more
wiley +1 more source
Grain refinement efficiency of a new oxide-containing master alloy for aluminium casting alloys [PDF]
In this study, grain refinement efficiency of a new oxide master alloy based on MgAl2O4 was demonstrated on an A357 alloy. The grain size of the reference alloy was reduced by 50-60% with the addition of the master alloy and introduction of ultrasonic ...
Dmitry G. Eskin +7 more
core +1 more source
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller +3 more
wiley +1 more source

