Results 81 to 90 of about 756,449 (301)
Advanced Engineering Materials, EarlyView.This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi +4 more
wiley +1 more source
EnergiesOrganic phase change materials (PCMs) have been used and studied for many years. In this work, we focus on an industrially available PCM—polyethylene waxes (PEW) modified with seven types of carbon black (CB) exhibiting different properties. Carbon black
Martyna Szatkowska +4 more
doaj +1 more source
The Amorphous-Crystal Interface in Silicon: a Tight-Binding Simulation [PDF]
, 1998 The structural features of the interface between the cystalline and amorphous phases of Si solid are studied in simulations based on a combination of empirical interatomic potentials and a nonorthogonal tight-binding model.
Aziz, M. J., Bernstein, N., Kaxiras, E.
core +2 more sources
Advanced Engineering Materials, EarlyView.This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani +2 more
wiley +1 more source
EnergiesThe global production of lemons and limes amounts to approximately 16 million tonnes annually, making these fruits among the most significant contributors to global citrus production.
Rafał Twaróg, Kinga Pielichowska
doaj +1 more source
Pharmaceutics, 2018 Amorphous solid dispersions are considered a promising formulation strategy for the oral delivery of poorly soluble drugs. The limiting factor for the applicability of this approach is the physical (in)stability of the amorphous phase in solid samples ...
Michael Brunsteiner +2 more
doaj +1 more source
Metals, 2020 Porous Copper (Cu) was brazed to Cu plates using Cu-9.7Sn-5.7Ni-7P amorphous filler metal. The effects of brazing parameters on the porous Cu and brazed joints were investigated. The furnace brazing temperatures employed were 660 °C and 680 °C,
Mian Muhammad Sami +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Strain Rate Effect on the Ductile Brittle Transition in Grinding Hot Pressed SiC Ceramics
Micromachines, 2020 Surface and subsurface damage are still persistent technical challenges for the abrasive machining hot pressed-silicon carbide (HP-SiC) ceramics. Therefore, an investigation of the material behavior and critical depth of ductile to brittle transition ...
Pai Huang, Jiaqi Zhang
doaj +1 more source
Advanced Engineering Materials, EarlyView.The growing demand for lightweight, nontoxic, and multifunctional gamma shielding materials has intensified efforts to find alternatives to conventional lead and aluminum‐based protectants. In this work, we develop epoxy quartz fabric composites reinforced with cobalt chloride (CoCl2) microparticles, fabricated via hand lay‐up with varying filler ...
Summan Urooge +7 more
wiley +1 more source