Results 31 to 40 of about 38,550 (309)

Laser Powder Bed Fusion of Copper–Tungsten Composites for Heat Sink Applications in High‐Power Electronics

Advanced Engineering Materials, EarlyView.
This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh, Shashank Deepak Prabhu, Jannik Huber, Lioba Fischer, Gerhard Wolf, Nico Hempel, Peter Mayr   +6 more
wiley   +1 more source

DESIGN OF INDUCTION COIL FOR OXYGEN FREE COPPER PRODUCTION

Journal of Engineering and Sustainable Development, 2021
This paper deals with the design of an induction coil (IC) intended to be used for an oxygen free copper production. This coil differs in design because it should be placed in a vacuum or in a chamber filled with noble gas, such as Argon.
Murtadha S. Kazem, Isam M. Abdulbaqi
doaj   +1 more source

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

Advanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal, Michael M. Becker, Sarah C. L. Fischer   +2 more
wiley   +1 more source

Dual‐Mode Film Based on Highly Scattering Nanofibers and Upcycled Chips‐Bags for Year‐Round Thermal Management

Advanced Functional Materials, EarlyView.
Intelligent radiative cooling devices, adaptable to various weather conditions, have the potential for year‐round energy savings. This study introduces a sustainable dual‐mode film made from polycaprolactone nanofibers and upcycled chip bags for effective thermal management.
Qimeng Song, Stefan Rettinger, Chengzhang Xu, Ulrich Mansfeld, Markus Retsch   +4 more
wiley   +1 more source

NUMERICAL RESEARCH OF THE MOISTURE CONDENSATION ELIMINATION IN THE CABIN OF THE UNIFIED TECHNOLOGICAL ELECTRIC TRANSPORT VEHICLE

Вестник СибАДИ, 2018
Introduction. This article deals with the problem of moisture condensation inside the cabin of the technological electric transport vehicle. The hypothesis of using the forced air ventilation in the cabin is substantiated, by which such problem could be ...
N. M. Filkin, A. M. Tatarkin
doaj   +1 more source

Positive‐Tone Nanolithography of Antimony Trisulfide with Femtosecond Laser Wet‐Etching

Advanced Functional Materials, EarlyView.
A butyldithiocarbamic acid (BDCA) etchant is used to fabricate various micro‐ and nanoscale structures on amorphous antimony trisulfide (a‐Sb2S3) thin film via femtosecond laser etching. Numerical analysis and experimental results elucidate the patterning mechanism on gold (reflective) and quartz (transmissive) substrates.
Abhrodeep Dey, Uwe Hübner, Albane Benardais, Xiaofei Wu, Andrea Dellith, Jan Dellith, Torsten Wieduwilt, Henrik Schneidewind, Markus A Schmidt, Virginie Nazabal, Volker Deckert, Jer‐Shing Huang, Wei Wang   +12 more
wiley   +1 more source

Experimental and numerical investigations of CFRP reinforced masonry ?beams performance under bending loads

Fracture and Structural Integrity, 2023
In this paper, an experimental and numerical study was achieved to investigate the behavior of masonry beams internally reinforced using carbon fiber-reinforced polymer (CFRP) and hybrid steel/CFRP reinforcements.
Mahmoud Zaghlal, Alaa El-Sisi�, Mohamed Husain, Samar Samy   +3 more
doaj   +1 more source

Micro and Nanostructural Diversity of Lizard Osteoderm Capping Tissue in Relation to Mechanical Performance

Advanced Functional Materials, EarlyView.
This study shows that lizard osteoderm capping tissue is a hyper‐mineralized hydroxyapatite layer consistently covering the superficial osteoderm surface in those species studied here, yet it varies greatly in morphology, nanostructure, and mechanical performance across species.
Adrian Rodriguez‐Palomo, Marius Didziokas, Malene Siri Berg Jacobsen, Thorbjørn Erik Køppen Christensen, Innokenty Kantor, Mads Ry Vogel Jørgensen, Klaus Pagh Almtoft, Jesper Skovhus Thomsen, Anthony Herrel, Catherine J.A. Williams, Henrik Birkedal   +10 more
wiley   +1 more source

Numerical nonlinear analysis of RC beams with un-strengthened and CFRP-strengthened opening drilled under service loads within shear zones

Fracture and Structural Integrity, 2023
The current research deals with the Reinforced Concrete (RC) beams numerical modeling using the finite element analysis software ANSYS-standard and the proposed strengthening procedure if it is urgently required to drill rectangular or circular in shape ...
Magdy Khalaf, Louay Aboul-Nour, Mahmoud Khater, Marwa Ibrahim   +3 more
doaj   +1 more source

Bio‐Inspired Magnetically Tunable Structural Colors from Elliptical Self‐Assembled Block Copolymer Microparticles

Advanced Functional Materials, EarlyView.
Cephalopod‐inspired photonic microparticles with dynamic structural coloration are fabricated via confined self‐assembly of linear block copolymers into ellipsoids containing stacked lamellae. Embedded superparamagnetic nanoparticles enable rapid magnetic alignment, restoring vivid, angle‐dependent color.
Gianluca Mazzotta, Simone Bertucci, Jose Mendoza‐Carreño, Agustín Mihi, Paola Lova, Davide Comoretto, Ullrich Steiner, Marco Lattuada, Andrea Dodero   +8 more
wiley   +1 more source