Results 11 to 20 of about 374 (167)
Influence of Austempering Temperatures on the Microstructure and Mechanical Properties of Austempered Ductile Cast Iron [PDF]
Metals, 2021 The influence of the austempering temperatures on the microstructure and mechanical properties of austempered ductile cast iron (ADI) was investigated. ADI is nodular graphite cast iron, which owing to higher strength and elongation, exceeds mechanical ...
Regita Bendikiene +8 more
doaj +6 more sources
Nodule count effect on microstructure and mechanical properties of hypo-eutectic ADI alloyed with nickel [PDF]
Journal of Mining and Metallurgy. Section B: Metallurgy, 2021 Samples of ductile iron alloyed with 0.88 % Ni with a nodule count of 606, 523, and 290 nod/mm2 were obtained from sand cast plates of different thickness in the range from 8.46 to 25.4 mm.
Colin-García E. +5 more
doaj +1 more source
Metals, 2021 The microstructural evolution and properties for varied austempering routes are investigated in a cold-rolled bainitic steel. Special attention is given to the effect of retained austenite (RA) in terms of its fraction, carbon concentration, and ...
Shuai Tang +3 more
doaj +1 more source
Statistical Data-Driven Model for Hardness Prediction in Austempered Ductile Irons
Metals, 2022 This research evaluates the effect of temperature and time austempering on microstructural characteristics and hardness of ductile iron, validating the results by means of a statistical method for hardness prediction.
Nelly Abigaíl Rodríguez-Rosales +8 more
doaj +1 more source
Austempering in Zamak bath: influence of austempering time and austenitizing temperatureon ductile cast iron properties [PDF]
Archives of Metallurgy and Materials, 2019 The combination of the austempered ductile iron mechanical properties strongly depend on the parameters used on the austempering cycle. On this study, the influence of austempering time and austenitizing temperature on the properties of a ductile iron ...
L. Pereira +5 more
doaj +1 more source
Microstructure and mechanical properties of two-step Cu-alloyed ADI treated by different second step austempering temperatures and times [PDF]
China Foundry, 2019 Austempering ductile iron (ADI) is an attractive material due to its excellent comprehensive mechanical properties. However, the deficit in elongation and toughness always threatens its security application.
Peng-yue Yi, Er-jun Guo, Li-ping Wang
doaj +1 more source
Rekayasa Mesin, 2023 Effect of austempering temperature on microstructure and mechanical properties gray cast iron with 10%wt nickel for boiler combustion application has been studied.
Fikri Widyansyah +2 more
doaj +1 more source
steel research international, Volume 94, Issue 9, September 2023., 2023 In this article, Franceschi et al. study a newly developed medium carbon high silicon carbide free baintic steel. The effect of different is isothermal transformation temperature on the bainitic microstructure is investigated in terms of phase constituents, morphology and mechanical properties. It is observed that the isothermal treatments below 300 °C
Mattia Franceschi +9 more
wiley +1 more source
Microstructure and mechanical properties of CuNiMo austempered ductile iron [PDF]
Journal of Mining and Metallurgy. Section B: Metallurgy, 2004 Microstructure and mechanical properties of Cu, Ni and Mo alloyed cast ductile iron have been investigated after austempering. Samples were austenitised at 860oC for 1h and then austempered at 320oC and 400oC in the interval from 0,5 to 5h.
Erić Olivera +3 more
doaj +1 more source
Advanced Engineering Materials, Volume 24, Issue 11, November 2022., 2022 Ensuring the transformation‐induced plasticity (TRIP) effect in advanced high‐strength steels (AHSS) requires that the formation of cementite is suppressed by the addition of alloying elements such as Si. Theoretical simulations reveal the impact of alloying elements on the elastic and chemical stability of cementite, taking into account the role of ...
Amin Sakic +3 more
wiley +1 more source