Results 91 to 100 of about 4,508 (168)
steel research international, EarlyView.Tailored heat treatments transform additively manufactured high‐nitrogen martensitic Cr steel from austenitic as‐built condition to high‐hardness states. Isothermal bainitizing at 250°C generates an ultrafine nanostructure and achieves higher hardness than conventional hardening and tempering, highlighting a promising postprocessing route for laser ...
Philip König +2 more
wiley +1 more source
steel research international, EarlyView.Serrations and stepwise austenite phase transformation were observed in cold‐rolled and annealed medium manganese steels. By in situ XRD experiments, these two phenomena were studied simultaneously. The results show that DSA leads to the creation of PLC bands and load drops in the specimen.
Shahroz Ahmed +6 more
wiley +1 more source
Effect of Pre - Heat- Treatment on Austenite Grain Size of Steel 508-3
Teshugang, 2013 Test steel 508-3 (/% : 0. 19C, 0. 26Si, 1.48Mn, 0. 009P, 0. 007S, 0. 78Ni, 0. 50Mo, 0.003Al) is melted by a vacuum induction furnace and cast to 50 kg ingot, forged at 1 150 to Φ16 mm bar, end forging ≥900℃.The effect of normalizing temperature (900 ~ 1 ...
何西扣, 刘正东, 林肇杰
doaj
steel research international, EarlyView.This review's second part details the mechanical, corrosion, and electromagnetic behaviors of FSSs. It integrates the foundational microstructure (texture/defects/precipitates) and processing effects from Part I to establish and analyze complex property–property interrelationships critical for high‐performance applications.
Shahab Bazri +2 more
wiley +1 more source
Novel Etching Technique for Delineation of Prior-Austenite Grain Boundaries in Low, Medium and High Carbon Steels. [PDF]
Materials (Basel), 2020 Thackray R, Palmiere EJ, Khalid O.
europepmc +1 more source
steel research international, EarlyView.The multi‐scale mechanical behavior of additive‐manufactured 316L stainless steel processed by directed energy deposition and high‐pressure torsion is explored. The influence of torsional strain on strength and microstructural evolution is revealed, indicating progressive grain refinement in the ultrafine regime, reaching strength levels nearing 1800 ...
M. Farhan Raza, Guney Guven Yapici
wiley +1 more source
steel research international, EarlyView.In primary electric arc furnace (EAF) steelmaking, carbon boiling removes nitrogen from liquid steel and sustains slag foaming. In 100% scrap‐ or hydrogen direct reduced iron (HDRI)‐based EAF steelmaking, carbon boiling is absent; therefore, carbonaceous material and oxygen injection into the slag is needed to maintain foaming and avoid nitrogen ...
Zushu Li +3 more
wiley +1 more source
steel research international, EarlyView.Despite increased hardness, elevated tramp element concentrations in a ferritic‐pearlitic low‐carbon steel lead to enhanced toughness accompanied by a more homogeneous and finer ferritic microstructure. Atom probe tomography reveals pronounced segregation of some tramp elements at grain boundaries and ferrite–cementite interfaces, together with ...
Lukas Hatzenbichler +6 more
wiley +1 more source
steel research international, EarlyView.Strain‐induced NbC precipitation governs hot‐deformation resistance in CrNiMnMoB ultrahigh‐strength steel by suppressing dynamic recrystallization, increasing activation energy, and refining martensitic substructures. The precipitation response is controlled by temperature, supersaturation, and strain rate, with slow deformation promoting extensive NbC
Atef Hamada +6 more
wiley +1 more source
steel research international, EarlyView.The effects of finishing rolling temperature, coiling temperature, and annealing on scale formation and pickling performance are studied. Scale morphology and composition are studied via SEM‐EDS, and pickling performance is studied by evaluating scale residues and mass losses during pickling.
Roosa Kähkönen +5 more
wiley +1 more source