Results 51 to 60 of about 148,325 (262)
Elastic modulus of reinforced concrete from bending test
CTU Journal of Innovation and Sustainable DevelopmentThis study demonstrates an experimental approach for direct measurement of RC elastic modulus. This work considered the transformed moment of inertia as an input variable.
TrustGod John +2 more
doaj +3 more sources
Bond and flexural strength of industrial cast UHPFRC-NC deck in Norway
Frontiers in Built EnvironmentA large portion of Norway’s aging bridge infrastructure requires rehabilitation due to environmental exposure. Ultra-High-Performance Fibre-Reinforced concrete (UHPFRC) overlays have emerged as a promising solution; however, their large-scale application
Malena Thomassen, Ingrid Lande
doaj +1 more source
Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading
Advanced Engineering Materials, EarlyView.This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Hybrid Cross-Laminated Timber under Bending: Finite Element Analysis Based on Nondestructive Testing
DrewnoThe growing demand for wood as a raw material, coupled with the impacts of climate change on coniferous forests, necessitates research into underutilized wood species and potential hardwood alternatives.
József Garab +2 more
doaj +1 more source
Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method
Advanced Engineering Materials, EarlyView.A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley +1 more source
Monitoring of Steel Road Barrier Flange by the Use of Barkhausen Noise as a Function of Its Yielding
MetalsThis study investigates the sensitivity of Barkhausen noise emission against the stress state as well as microstructure alterations in the steel road barrier flange.
Katarína Zgútová +4 more
doaj +1 more source
Hybrid Metal–Carbon Ink for Printed Stretchable Temperature Sensors
Advanced Engineering Materials, EarlyView.We prepare conductive inks for temperature sensing with silver flakes and carbon or graphite flakes in a silicone elastomer matrix. Silver dominates the temperature‐dependent conductivity, while the carbon filler network ensures the stability of the conductive pathways and retains function under strain.
Makara Lay +3 more
wiley +1 more source
PRACTICAL STUDY ON THE CFRP REINFORCEMENT [PDF]
Fiabilitate şi Durabilitate, 2016 One of the defining goals of this paper is getting new resistant material which combine the qualities of basic materials that get into its composition but not to borrow from them their negative properties.
Catalina IANASI
doaj
Advanced Engineering Materials, EarlyView.Functionally graded metal–ceramic femoral stems are engineered through continuous UMAT‐based stiffness tailoring, eliminating discrete material interfaces while enhancing biomechanical compatibility. Low‐index power‐law gradation optimizes load transfer, reduces stress shielding, and controls implant–bone micromotion, highlighting a materials‐design ...
Rihem Nouira, Sameh Elleuch, Hanen Jrad
wiley +1 more source