Results 121 to 130 of about 590,085 (277)

Synthesis and Characterization of Acrylate‐Based Block and Block‐Graft Copolymers Using Polyester‐Based Macro‐RAFT Agents Through Two‐Step Polymerization and Assessment of One‐Pot Epoxy Group Ring‐Opening Modification

Polymer Engineering &Science, EarlyView.
Schematic diagram of RAFT polymerization of acrylate monomers. ABSTRACT This study reports the synthesis of a macro‐RAFT agent based on poly(ɛ‐caprolactone) (PCL) via ring‐opening polymerization (ROP), which was subsequently used to prepare acrylate‐based block and block‐graft copolymers through RAFT polymerization.
Melahat Göktaş, Cengiz Aykaç
wiley   +1 more source

Graphene and its modifications for enhanced adhesion in dental restoratives: a molecular docking and dynamics study

Scientific Reports
Graphene has attracted significant attention in dentistry due to its structural and adhesive properties, enhancing the mechanical performance of dental composites.
Mohammad Ali Saghiri, Ravinder S Saini, Mohamed Saheer Kuruniyan, Seyed Ali Mosaddad, Artak Heboyan   +4 more
doaj   +1 more source

Impact of polymer aging on main‐chain poly(fullerene)s with halide chain‐ends for inverted perovskite solar cells

Polymer International, EarlyView.
Subtle variations in halogen chemistry significantly affect the aging behavior of polymeric electron transport layers in inverted perovskite solar cells, underscoring the importance of precise chemical design for enhancing long‐term stability. Abstract As perovskite solar cells (PSCs) advance toward commercialization, the need for stable and easily ...
João V. Paulin, Gabriel L. Nogueira, Douglas H. N. Santos, Marco Antônio G. B. Gomes, Valdemiro P. Carvalho‐Jr, Luiz C. Silva Filho, Roger C. Hiorns, Carlos F. O. Graeff   +7 more
wiley   +1 more source

Effect of APTES- or MPTS-Conditioned Nanozirconia Fillers on Mechanical Properties of Bis-GMA-Based Resin Composites. [PDF]

ACS Omega, 2020
Yang J, Liao M, Hong G, Dai S, Shen J, Xie H, Chen C.   +6 more
europepmc   +1 more source

Estudo da microinfiltração marginal de sistemas adesivos universais experimentais, com e sem Bis-GMA, na vertente self-etch

, 2021
Dissertação para obtenção do grau de Mestre no Instituto Universitário Egas MonizObjetivo: Avaliar a microinfiltração marginal de dois sistemas adesivos universais experimentais, com e sem Bis-GMA e de dois sistemas adesivos universais comerciais com Bis-
Matão, André Gonçalo Teodoro
core  

Main‐chain polyfullerenes: Taking fullerene to the next dimension

Polymer International, EarlyView.
This short review appraises main‐chain polyfullerenes. Their slow development over 30 years has suddenly boomed with a rapid growth due to exciting developments in solar energy. Abstract This mini‐review gives an overview of the development, chemistry, properties and applications of main‐chain polyfullerenes.
Marco Antônio GB Gomes, Orisson Ponce Gomes, Patricia Targon Campana, Didier Bégué, Roger C Hiorns   +4 more
wiley   +1 more source

Copolymer Synthesis of N‐Vinylacetamide and 2‐Methylene‐1,3‐Dioxepane Provides a New Degradable Polymer

Journal of Polymer Science, Volume 63, Issue 6, Page 1306-1318, 15 March 2025.
ABSTRACT N‐vinylamides, especially noncyclic N‐vinylacetamide (NVA), have been used in various applications such as biomaterials, surfactants, and hydrogels. However, their potential to copolymerize with cyclic ketene acetal (CKA) to create degradable polymers is underexplored.
Mukmin Sapto Pamungkas, Tsuyoshi Ando, Hiroharu Ajiro   +2 more
wiley   +1 more source

Rheological properties of experimental Bis-GMA/TEGDMA flowable resin composites with various macrofiller/microfiller ratio.

, 2009
OBJECTIVES: The purpose of this study was to investigate the rheological behavior of resin composites and to evaluate the influence of each component, organic as well as inorganic, on their viscoelastic properties by testing model experimental ...
Dabin, Anne, Beun, Sébastien, Bailly, Christian, Vreven, José, Leloup, Gaëtane, Devaux, Jacques   +5 more
core   +1 more source

In Situ Curing‐Enabled 3D Printing of Continuous Fiber‐Reinforced Thermosetting Composites

Journal of Polymer Science, EarlyView.
In situ curing‐enabled the 3D printing of continuous fiber/thermoset composites, which were reviewed. Particularly, four types of in situ curing, were discussed, including Radiation‐induced curing, photothermal curing, electrothermal curing, and frontal polymerization. AI‐integrated printing was also analyzed.
Xiaofei Wu, Harrison Hayworth, Shiren Wang   +2 more
wiley   +1 more source

Effect of Type and Concentration of Nanoclay on the Mechanical and Physicochemical Properties of Bis-GMA/TTEGDMA Dental Resins. [PDF]

Polymers (Basel), 2020
Encalada-Alayola JJ, Veranes-Pantoja Y, Uribe-Calderón JA, Cauich-Rodríguez JV, Cervantes-Uc JM.   +4 more
europepmc   +1 more source