Results 1 to 10 of about 332,876 (331)

Observation and prediction of bottom collapse and middle break phenomena in the blasting demolition of high chimneys [PDF]

open access: yesScientific Reports
In order to solve the key problems affecting the safety of the project, such as the collapse of the support part and break in the air of the reinforced concrete chimney during the blasting demolition, this paper carried out systematic monitoring and ...
Qiang Li   +5 more
doaj   +2 more sources

Evaluation of the impact of blast damage on tunnel surrounding rock induced by C-type cumulative tube cone angle [PDF]

open access: yesScientific Reports
Over-excavation and under-excavation are common issues in tunnel construction using the drilling and blasting method. In some cases, traditional blasting techniques may fail to achieve the desired results.
Jian Guo   +5 more
doaj   +2 more sources

Lateral spreading mitigation in gravity quay walls backfilled with coral sand through electrolysis desaturation treatment [PDF]

open access: yesScientific Reports
Quay walls constructed on hydraulically filled coral sand deposits face inevitable liquefaction-induced hazards during seismic events. For mitigation, electrolysis method can be employed as an induced partial saturation technique to improve the ...
Junwei Guo   +5 more
doaj   +2 more sources

Intelligent Debonding Detection in GFRP Rock Bolts via Piezoelectric Time Reversal and CNN-SVM Model [PDF]

open access: yesSensors
To address the challenge of detecting debonding damage in glass-fiber-reinforced polymer (GFRP) rock bolt anchorage structures, this study proposes a time reversal detection method based on piezoelectric sensing and a Convolutional Neural Network–Support
Zhenyu Zhang   +5 more
doaj   +2 more sources

A strategy to introduce multi-gradient structures into iron by explosive shock wave processing

open access: yesJournal of Materials Research and Technology, 2023
A strategy combining shock-induced phase transition, twins, and dislocations to produce a multi-gradient structure in Fe is designed and proposed by the explosive processing method. A specific emulsion explosive is designed to introduce gradient pressure
Jianian Hu   +5 more
doaj   +1 more source

Some results of the study of rock properties of the Sulukta deposit [PDF]

open access: yesE3S Web of Conferences, 2023
This article presents the results of research into the properties of physical and mechanical properties of rocks and their influence on the conditions of their occurrence in the coal-bearing massif, depending on the geological structure of a particular ...
Kazatov Urmat   +5 more
doaj   +1 more source

Study on blast-induced ground vibration velocity limits for slope rock masses

open access: yesFrontiers in Earth Science, 2023
Seismic waves induced by blasting can cause damage to slope rock masses and thus lower the stability of the slope. The vibration standards of many countries do not specify the allowable blasting vibration velocity for slope rock masses.
Jinshan Sun   +7 more
doaj   +1 more source

BLAST++: BLASTing queries in batches [PDF]

open access: yesBioinformatics, 2003
Abstract Summary: BLAST++ is a tool that is integrated with NCBI BLAST, allowing multiple, say K, queries to be searched against a database concurrently. The results obtained by BLAST++ are identical to that obtained by executing BLAST on each of the K queries, but BLAST++ completes the processing in a much shorter time ...
Wang, H.   +4 more
openaire   +2 more sources

PPV Criterion of a Defect Rock Slope under Blasting SV-Waves

open access: yesShock and Vibration, 2022
In order to estimate the stability of slopes with geological defects during blasting excavations, the dynamic responses of a rock slope with a fault subjected to blasting seismic waves are studied. The SV-component of blasting seismic waves is considered
Shiwei Lu   +4 more
doaj   +1 more source

Effect of Perchlorate on Combustion Properties of Directly-Written Al/PVDF Composites

open access: yesFire, 2023
Metastable intermolecular composites (MICs) based on Al/PVDF have become one of the most important materials in the field of additive manufacturing of energetic materials due to their high energy density and designability.
Jingwei Li   +5 more
doaj   +1 more source

Home - About - Disclaimer - Privacy