Results 31 to 40 of about 18,483 (267)

Light‐Assisted 3D Printing Techniques and Photocrosslinking Strategies: Recent Advances in Musculoskeletal Tissue Engineering

Advanced Engineering Materials, EarlyView.
In this review, the current state of light‐assisted 3D printing as it pertains to engineering musculoskeletal tissues including bone, cartilage, skeletal muscle, tendon, and ligaments is summarized. Common printing techniques, photoreactive materials, and study design choices are compiled and reviewed.
Meagan Morgan, Bin Zhang, Roger Narayan
wiley   +1 more source

Variable Stiffness Flexure Structures Enabled by Phase‐Change Gallium and Adhesive Interfacial Locking for Soft Robotic Applications

Advanced Engineering Materials, EarlyView.
A flexure‐based variable stiffness structure is developed by integrating phase‐change modulation and adhesive interfacial locking of gallium. The design enables a wide stiffness variability, transitioning from soft, flexible behavior to rigid, load‐supporting performance.
Sungjin Kim, Sohee John Yoon, Yong‐Lae Park   +2 more
wiley   +1 more source

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source

Diffusion bonding of nickel-based powder metallurgy superalloy FGH98 with pure nickel interlayer

Journal of Materials Research and Technology
FGH98 powder metallurgy superalloy were successfully bonded via diffusion bonding technique with pure Ni interlayer. It was indicated that adding the Ni interlayer can significantly reduce joint defects, promote elements diffusion, and improve the ...
Wei Guo, Jingru Xin, Ding Hao, Yana Ma, Jiangtao Xiong, Jinglong Li, Qinghua Feng   +6 more
doaj   +1 more source

Adhesively bonded single lap joint of composites

Ciencia y Poder Aéreo, 2013
A study of single lap joints of composite materials with and without attachments is presented. Failure of this type of joint is caused by the high peel stress in a perpendicular direction presented in the geometric singularity. It is shown that the joint
Peter Alvarado Prieto
doaj   +1 more source

Fostering Innovation: Streamlining Magnetocaloric Materials Research by Digitalization

Advanced Engineering Materials, EarlyView.
Magnetocaloric cooling (MCE) is an environmentally friendly refrigeration method with great potential. Optimizing MCE materials involves the preparation and screening of large quantities of samples, which in turn generates a large amount of data. A digitalization approach is presented that uses ontologies, knowledge graphs, and digital workflows to ...
Simon Bekemeier, Moritz Blum, Luana Caron, Alisa Chirkova, Philipp Cimiano, Basil Ell, Inga Ennen, Michael Feige, Maik Gaerner, Thomas Hilbig, Andreas Hütten, Günter Reiss, Tapas Samanta, Sonja Schöning, Christian Schröder, Lennart Schwan, Chris Taake, Martin Wortmann   +17 more
wiley   +1 more source

Influence of hydrothermal ageing on single lap bonded CFRP joints [PDF]

Fracture and Structural Integrity, 2018
Nowadays adhesive are widely used in structural applications, in particular for assembly composite materials. In fact, this technique allows to obtain a more uniform load in the joint, to realise a joint with an higher specific strength and to avoid ...
Costanzo Bellini, Gianluca Parodo, Wilma Polini, Luca Sorrentino   +3 more
doaj   +2 more sources

Analysis of stress distribution of CFRP bonded joints: A study of numerical and machine learning approach

Heliyon
We aim to provide a study of material selection at the upper adherend subject for optimization of carbon fiber reinforced polymer (CFRP) adhesive-bonded joints with details on the stress distribution in the complex tri-material joint structure.
Shah Mohammad Azam Rishad, Md Ashraful Islam, Md Shahidul Islam   +2 more
doaj   +1 more source

Effects of steps on the load bearing capacity of 3D-printed single lap joints

Journal of Materials Research and Technology, 2023
Damage in adhesively bonded joints typically initiates in the overlap area due to high level of bonding (peel) stress. Different approaches are being considered to decrease the peel stress and improve the overall strength of the joint.
Mohammad Reza Khosravani, Payam Soltani, Tamara Reinicke   +2 more
doaj   +1 more source

Is an Apple an Orange? A Large Language Model Benchmark for Candidate Term Extraction and Subclass Decisions Against Upper Ontologies in Engineering and Materials Science

Advanced Engineering Materials, EarlyView.
Building machine‐readable vocabularies for materials science is slow, expert‐driven work. This study benchmarks 13 large language models on two of its first steps: finding candidate terms in engineering articles and deciding where they belong in a class hierarchy.
Thomas Bjarsch, Maximilian Holland, Klaus Drechsler, Johannes Schilp   +3 more
wiley   +1 more source