Results 191 to 200 of about 2,691,137 (248)

Effect of Temperature on Tensile Properties of Electrospun Nanofibre Interleaved Carbon Composites

open access: yesPolymer Composites, EarlyView.
Thermal Durability of Electrospun Nanofibre Interleaved Composites. ABSTRACT Carbon fiber composites are susceptible to brittle damage modes such as matrix cracking and delamination. The inception and propagation of these invisible damages are responsible for loss in load‐bearing capacity and accelerating environmental degradation.
Usaid Ahmed Shakil   +5 more
wiley   +1 more source

Tribological Behavior of Additively Manufactured Dual‐Material Polymer Composites

open access: yesPolymer Composites, EarlyView.
Layered architecture, tribological performance, and wear mechanisms of additively manufactured dual‐material hybrid polymer composites. ABSTRACT This study presents a novel material design approach for wear‐resistant sandwich‐structured hybrid composites fabricated using dual‐nozzle fused deposition modeling (FDM). By co‐printing commercially available
Zhiwang Li   +3 more
wiley   +1 more source

Dynamic Mechanical Response of Flax Roving Under Controlled Thermo‐Hygrometric Conditions

open access: yesPolymer Composites, EarlyView.
Schematic illustration of the effects of moisture and temperature on the mechanical and structural properties of flax rovings. ABSTRACT This work investigates the coupled effects of temperature and relative humidity on the mechanical, thermal, damping, and structural responses of flax roving fibers.
Bernard Miranda Campos   +4 more
wiley   +1 more source

Enhancing the Interface of PLA Composites Through Solution‐Based Processing

open access: yesPolymer Composites, EarlyView.
Schematic representation of each microbond sample preparation method: tying versus solution casting. Solution cast samples exhibited higher apparent interfacial shear strengths across all fibre types and a distinct failure mechanism. ABSTRACT The strength of the fiber‐matrix interface plays a critical role in controlling the mechanical performance of ...
Innes McKay, Liu Yang, Reda Felfel
wiley   +1 more source

Experimental and Numerical Assessment of Progressive Damage in CF/PEEK Laminates Under Monotonic and Progressive Cyclic Four‐Point Bending

open access: yesPolymer Composites, EarlyView.
Experimental four‐point bending of CF/PEEK laminates under monotonic and progressive cyclic loading is assessed using classical lamination theory and a calibrated Hashin progressive damage model. ABSTRACT Carbon‐fiber‐reinforced PEEK composites combine high specific strength, corrosion resistance, and damage tolerance, supporting their use in aerospace,
Pedro Antônio Castro Regio dos Santos   +5 more
wiley   +1 more source

Investigation of Porosity and Cell Wall Swelling in Sisal Yarn Reinforced Polylactic Acid Composites

open access: yesPolymer Composites, EarlyView.
Key findings on the effects of NaOH treatment on sisal yarn reinforced PLA composites. ABSTRACT Growing demand for sustainable materials is increasing attention in biocomposites based on natural fibers and biodegradable polymers. This study investigates the influence of porosity and cell swelling in sisal yarn reinforced polylactic acid (PLA ...
Clemence Robinson Ansbert   +3 more
wiley   +1 more source

Development of Sustainable Cellulose Acetate‐Based Filaments for 3D Printing Through Plasticization and Natural Wax Incorporation

open access: yesPolymer Engineering &Science, EarlyView.
Schematic illustration of the forest‐derived filament production for 3D‐printing. ABSTRACT The integration of renewable biopolymers into value‐added engineering applications has become more critical. Cellulose acetate (CA) is a naturally derived polymer and widely used in the design‐oriented optical industry.
Naile Angın, Mesut Uysal
wiley   +1 more source

Mechanical and Impact Response of Adhesively Bonded ASA/PA12 Sandwich Structures Produced by Fused Filament Fabrication

open access: yesPolymer Engineering &Science, EarlyView.
Adhesively bonded ASA/PA12 FFF sandwich structures reveal that interfacial compliance governs mechanical performance. Cyanoacrylate enhances strength but induces brittle failure, while polyurethane improves ductility and impact resistance, demonstrating that adhesive properties and stacking sequence are critical design parameters for optimizing multi ...
Berkay Ergene   +3 more
wiley   +1 more source

Simulation of the Rotational Molding Process of Polyethylene Using the Smoothed Particle Hydrodynamics Method

open access: yesPolymer Engineering &Science, EarlyView.
Numerical simulation of polyethylene rotational molding using the Smoothed Particle Hydrodynamics (SPH) method. ABSTRACT This work presents the development of a numerical model based on the smoothed particle hydrodynamics (SPH) method to simulate the rotational molding process of powder thermoplastic polymers, used in the manufacture of liners for high‐
Ali Nourreddine   +4 more
wiley   +1 more source

Decoupling Formulation and Processing Effects in Thermoplastic Starch Through a Data‐Driven Structure–Property Framework

open access: yesPolymer Engineering &Science, EarlyView.
Processing‐property relationships in thermoplastic starch (TPS): plasticizer type, starch source and melt‐processing temperature establish a hierarchy of effects that governs process‐induced changes and the resulting TPS properties. ABSTRACT Thermoplastic starch (TPS) is a melt‐processable biopolymer whose properties depend strongly on formulation and ...
Cristina Pavón   +3 more
wiley   +1 more source

Home - About - Disclaimer - Privacy