Results 21 to 30 of about 2,387,804 (309)
Crystals, 2017 In order to reduce the dislocation density and improve the performance of high indium content In0.82Ga0.18As films, the design of double buffer layers has been introduced into the In0.82Ga0.18As/InP heterostructure.
Liang Zhao +6 more
doaj +1 more source
AIP Advances, 2018 Buffer layer dependence of tunnel magnetoresistance (TMR) effects was investigated in Co2Fe0.4Mn0.6Si (CFMS)/MgO/Co50Fe50 magnetic tunnel junctions (MTJs).
Mingling Sun +5 more
doaj +1 more source
Nanoscale Research Letters, 2022 High-quality four-layer molybdenum disulfide (MoS2) nanosheets with lateral dimension of about 11 µm were prepared by ultrasonic treatment of MoS2 powder with assistance of 1-methyl-2-pyrrolidone (NMP) solvent.
Xingwang Jiang +4 more
doaj +1 more source
Sensors, 2017 The UV-to-visible rejection ratio is one of the important figure of merits of GaN-based UV photodetectors. For cost-effectiveness and large-scale fabrication of GaN devices, we tried to grow a GaN epitaxial layer on silicon substrate with complicated ...
Chang-Ju Lee +4 more
doaj +1 more source
Towards high-efficiency CZTS solar cell through buffer layer optimization
Materials for Renewable and Sustainable Energy, 2019 Cu2ZnSnS4 (CZTS)-based solar cells show a promising performance in the field of sunlight-based energy production system. To increase the performance of CZTS-based solar cell, buffer layer optimization is still an obstacle.
Farjana Akter Jhuma +2 more
doaj +1 more source
Hyperosmotic stress induces PARP1‐mediated HPF1‐dependent mono(ADP‐ribosyl)ation
FEBS Letters, EarlyView.Sorbitol‐induced hyperosmotic stress rapidly induces reversible mono(ADP‐ribosyl)ation (MARylation) on PARP1 without the signs of genotoxic signaling. We show that PARP1 autoMARylation is HPF1 dependent and forms hydroxylamine‐resistant O‐glycosidic linkages.
Anna Georgina Kopasz +11 more
wiley +1 more source
Dynamic conductive property and mechanism of buffer tape in HV XLPE cables
电力工程技术, 2022 Ablation of the buffer layer in high voltage cross-linked polyethylene (XLPE) cables has been the attractive type of cable failure. The ablation of buffer layer commonly takes place under the pressure and moisture.
MEN Yekun +5 more
doaj +1 more source
Buffer layers in heterostructures
Modern Electronic Materials, 2017 This work deals with the problem of choosing buffer layer architectures in the development of standard heterostructure models with controlled levels of mechanical stresses and low defect densities in the bulk and at layer boundaries. It has been found that these parameters depend on the quality of the source wafer surface, the wafer preparation ...
openaire +2 more sources
FEBS Letters, EarlyView.We present robust protocols for the preparation of supported lipid bilayers (SLBs) incorporating either Salmonella smooth LPS or outer membrane vesicles (OMVs). We use a combination of quartz crystal microbalance with dissipation (QCM‐D) and fluorescence microscopy to both characterize the SLBs of various compositions and to probe their interactions ...
Hudson P. Pace +6 more
wiley +1 more source
Infrared spectroscopic analysis of ablative gases in the buffer layer of high-voltage cables
电力工程技术Ablative defects in the buffer layer of high-voltage cables are important causes of power cable failures. Buffer layer ablation releases gases, and some components of these gases and their concentrations can characterize the degree of buffer layer ...
Yekun MEN +5 more
doaj +1 more source