Results 191 to 200 of about 8,899 (284)

Effect of Heat Treatment Parameters on Microstructure, Hardness, and Corrosion Resistance of Martensitic Stainless Steel X30Cr13 (AISI 420B)

Materials and Corrosion, EarlyView.
The hardness and corrosion resistance of the martensitic stainless steel X30Cr13 depend directly on the applied heat treatment. This article describes and discusses the relationships between alloy composition, thermodynamic phase stabilities, heat treatment parameters, resulting microstructures, and achievable corrosion resistance. To investigate these
Adrian Evia Ocampo, Saskia Roßberg, Jann Rohr, Paul Rosemann   +3 more
wiley   +1 more source

Effect of Tempering Temperature on Microstructural Evolution and Mechanical Properties of Cr-Ni-Mo-V Steel for Pressure Vessel Applications. [PDF]

Materials (Basel)
Liang E, Liang X, Yang Y, Yu W, Xu L, Wang M, Shi J.   +6 more
europepmc   +1 more source

Laser deposition of Inconel 625/tungsten carbide composite coatings by powder and wire feedstock

There is an increasing global demand to extend the life span of down-hole drilling tools in order to improve operation effectiveness and efficiency of oil and gas production.
Abioye, Taiwo E.
core  

Failure Investigation of Alloy 625 Sockolets After Prolonged Service in an Ammonia Cracker Unit

Materials and Corrosion, EarlyView.
The failure of the sockolets was caused by intergranular cracking and fracture. The thick and highly brittle nitrided layer formed intergranular surface cracks, which propagated along grain boundaries into the base alloy substrate due to the presence of brittle Cr‐rich carbides. ABSTRACT Several sockolets of Alloy 625 operating at 540°C in contact with
Kamlesh Chandra, N. Naveen Kumar, Niraj Kumar   +2 more
wiley   +1 more source

Effects of Annealing Temperature on Interfacial Structure and Thermal Conductivity of Hot-Pressed Copper/Cr-Coated Diamond Composites. [PDF]

Materials (Basel)
Liu Y, Chen X, Liu Y, Tian W, Zhou F, Zhou H, Wang Y.   +6 more
europepmc   +1 more source

Experimental and Comparative Study of the Corrosion Behavior of Lean Duplex Stainless Steel in Seawater

Materials and Corrosion, EarlyView.
The localized corrosion behavior of lean duplex stainless steel EN 1.4062 is systematically compared with austenitic and higher‐alloyed duplex grades in natural seawater. A clear resistance ranking is established, highlighting EN 1.4062 as a cost‐effective alternative for limited marine exposure.
Mohammad Hassanzadeh, Nicolas Larché, Audrey Allion‐Maurer, Raf Dewil, Barbara Rossi   +4 more
wiley   +1 more source

Reactive Carbide-Based Synthesis and Microstructure of NASICON Sodium Metal All Solid-State Electrolyte. [PDF]

Adv Mater
Campbell CJ, Monismith S, Raj V, Wang Y, Yan Q, Fincher CD, Raj R, Chiang YM, Watt J, McBrayer JD, Mitlin D.   +10 more
europepmc   +1 more source

Machine Learning Design of Tungsten Alloys With Strength–Ductility Synergy

Materials Genome Engineering Advances, EarlyView.
This study integrates machine learning with solid solution softening knowledge to design multielement tungsten alloys with strength‐ductility synergy. ML models identify promising compositions within W‐ Ta ‐ Re system that exhibit pronounced chemical short‐range order, resulting in exceptional mechanical performance. Experimental validation through the
Juan Ding, Jiayi Liu, Jiatao Zhou, Baishan Chen, Yunzhu Ma, Wensheng Liu, Yufeng Huang, Chaoping Liang   +7 more
wiley   +1 more source

Effect of Mo₂C Addition on Microstructure and Wear Behavior of HVOF Carbide-Metal Composite Coatings. [PDF]

Materials (Basel)
Chen F, Xia X, Wang W, Gong X, Yuan X, Tang C, Lou X, Guo Z, Wang L, Wu B, Zhu Y, Yang M.   +11 more
europepmc   +1 more source

Interface Phonon Transmission Behaviors and Their Resultant Influence on Thermal Transport in Cu/Diamond Composites

Materials Genome Engineering Advances, EarlyView.
Cu/diamond heat spreaders are limited by low thermal boundary conductance. Using DFT + DMM, we identify the phonon‐transport factors governing TBC and show that optical–phonon contributions and branch conversion are essential. High‐k $k$ carbides (B4C, WC) and residual B and Cr improve interfacial heat transfer, enabling robust performance versus ...
Qinghe Zheng, William Yi Wang, Leandro Bolzoni, Fei Yang   +3 more
wiley   +1 more source