Dynamics of chip formation during the cutting process using imaging techniques: A review
International Journal of Mechanical System Dynamics, 2022 Imaging techniques have been widely implemented to study the dynamics of chip formation. They can offer a direct method and a full field measurement of the cutting process, providing kinematic information of the chip formation process.
Guangchao Nie +5 more
doaj +2 more sources
Influence of Feed Rate Response (FRR) on Chip Formation in Micro and Macro Machining of Al Alloy
Metals, 2021 In this paper, the investigation of chip formation of aluminum alloy in different machining strategies (i.e., micro and macro cutting) is performed to develop a holistic view of the chip formation phenomenon.
M. Azizur Rahman +11 more
doaj +2 more sources
Influence of Technological Parameters on Chip Formation and Chip Control in Precision Hard Turning of Ti-6Al-4V [PDF]
Micromachines, 2023 This article presents the results of an experimental investigation into the effect of process parameters in the precision hard turning of Ti-6Al-4V on chip morphology at both macro and micro levels.
Elshaimaa Abdelnasser +4 more
doaj +2 more sources
Chip Formation Mechanism of Inconel 718: A Review of Models and Approaches
Chinese Journal of Mechanical Engineering, 2021 Inconel 718, a nickel, chrome and iron alloy, has special advantages, such as high-temperature strength, thermal resistance and corrosion resistance, which facilitate wide usage in the aerospace industry, especially in the hot sections of gas turbine ...
Chun Liu +3 more
doaj +2 more sources
Mechanisms and FEM Simulation of Chip Formation in Orthogonal Cutting In-Situ TiB₂/7050Al MMC. [PDF]
Materials (Basel), 2018 The in-situ TiB2/7050Al composite is a new kind of Al-based metal matrix composite (MMC) with super properties, such as low density, improved strength, and wear resistance.
Xiong Y, Wang W, Jiang R, Lin K, Shao M.
europepmc +2 more sources
The microstructure infl uence on the chip formation process of Al-Cu alloy cast conventionally and in semi solid state [PDF]
Metalurgija, 2012 For many metal alloys, the process of metal cutting is accompanied by extensive plastic deformation and fracture. To study this process, quick stop sectional samples of hypoeutectic Al-Cu alloy chip formation, either as conventionally cast alloy or as ...
P. Kovač +4 more
doaj +1 more source
Analysis of the Material Removal Process in Precision Milling of AZ91D Magnesium Alloy [PDF]
MicromachinesThe study investigated the material removal process during precision milling of AZ91D magnesium alloy. A high-speed camera enabling high-frequency image recording was used to observe the cutting zone.
Jarosław Korpysa
doaj +2 more sources
Chip Formation of Rounded Cutting Edges
International Journal of Precision Engineering and Manufacturing, 2019 In cutting processes, the performance and tool life of cutting tools are important evaluation criterions. The cutting edge microgeometry of the tools is in direct contact with the workpiece and thus influences the material flow and the loads on the cutting wedge.
B. Bergmann +3 more
openaire +2 more sources
Analysis of Microstructure and Chip Formation When Machining Ti-6Al-4V
Metals, 2018 Microstructure and chip formation were evaluated during the step shoulder down-milling of Ti-6Al-4V using a water-miscible vegetable oil-based cutting fluid.
Islam Shyha +3 more
doaj +2 more sources
The effect of chip formation on the cutting force and tool wear in high-speed milling Inconel 718
The International Journal of Advanced Manufacturing Technology, 2023 Coated carbide tools are widely used in the processing of nickel-based superalloys due to their excellent wear resistance, high strength, and good hardness at high temperatures.
Guoqing Zhang +4 more
semanticscholar +1 more source