Results 111 to 120 of about 2,393,062 (304)

Neighborhood Socioeconomic Status and Short‐Term Functional Outcomes in Systemic Lupus Erythematosus

open access: yesArthritis Care &Research, Accepted Article.
Objective Individuals with SLE can accumulate functional status (FS) impairment. We evaluated the association between neighborhood socioeconomic disadvantage, as measured by the area deprivation index (ADI), and FS in a national SLE sample. Methods Data were derived from RISE, a national electronic health record‐based registry.
Baljeet Rai   +7 more
wiley   +1 more source

Evaluating Marine Stratocumulus Clouds in the CNRM‐CM6‐1 Model Using Short‐Term Hindcasts

open access: yesJournal of Advances in Modeling Earth Systems, 2019
The representation of stratocumulus by the atmospheric component of the Centre National de Recherches Météorologiques model version 6 (CNRM‐CM6‐1) is assessed.
Florent Brient   +2 more
doaj   +1 more source

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

open access: yesAdvanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai   +2 more
wiley   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

open access: yesAdvanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira   +4 more
wiley   +1 more source

Prediction of Surface Topography Parameters in Direct Laser Interference Patterning of Stainless Steel Using Infrared Monitoring and Convolutional Neural Networks

open access: yesAdvanced Engineering Materials, EarlyView.
This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky   +5 more
wiley   +1 more source

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

open access: yesAdvanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé   +5 more
wiley   +1 more source

On the Influence of Antioxidants and Recycled MgO–C Source Material on the Mechanical Properties of Carbon‐Bonded Magnesia Refractories

open access: yesAdvanced Engineering Materials, EarlyView.
The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann   +6 more
wiley   +1 more source

Climate, Climate Modeling, and Forecasting

open access: yes
Abstract This study assesses future climate change in Qatar under three IPCC greenhouse gas emission scenarios: SSP1-2.6, SSP2-4.5, and SSP5-8.5. Using multi-model simulations made under IPCC’s CMIP6, projected changes in seasonal and annual mean temperature, heat stress index, and rainfall are analyzed for three future periods—the ...
K. K. Kanikicharla   +6 more
openaire   +1 more source

Toward Low‐Consumable Anodes: Process Simulation and Prospective Life Cycle Assessment of NiFe2O4‐NiO‐Ni‐Cu vs. Prebaked Anodes for Aluminum Production with use of Molten Salt Electrolysis

open access: yesAdvanced Engineering Materials, EarlyView.
Low‐consumable nickel ferrite‐based anodes for the Hall–Héroult process are compared with conventional prebaked carbon anodes using thermodynamic simulation and prospective life cycle assessment under contrasting future electricity system pathways from 2025 to 2050.
Felipe Alejandro Garcia Paz   +6 more
wiley   +1 more source

Home - About - Disclaimer - Privacy