Results 11 to 20 of about 63,948 (294)
Metals, 2020 In this work, the effect of drawing pass on the surface layer softening or plasticizing of Q235 steel bar during electrochemical cold drawing (ECD) was studied, as well as cold drawing in air (DIA) for comparison.
Jangli Guo, Tijun Chen, Bo Li
doaj +2 more sources
Effect of Cold Drawing on Mechanical Properties of Biodegradable Fibers [PDF]
Journal of Applied Biomaterials & Functional Materials, 2017 Purpose Biodegradable polymers are currently gaining importance in several fields, because they allow mitigation of the impact on the environment related to disposal of traditional, nonbiodegradable polymers, as well as reducing the utilization of oil-based sources (when they also come from renewable resources).
La Mantia, Francesco Paolo +3 more
openaire +5 more sources
Practice of Cold Drawing Process Optimization of GCr15 Bearing Steel Rod
Teshugang, 2015 The effect of draft, cone angle and length of sizing belt of drawing die, and drawing speed on drawing stress and drawing surface accuracy of bearing steel GCr15 (1. 01% C, 1. 58% Cr) Φ11 mm rod coil has been analyzed. The optimization process for Φ11 mm
王莹莹, 杨鹏远
doaj +1 more source
Cold resistance of steel beam prestressed by wall drawing
Вестник СибАДИ, 2023 Introduction. The purpose of the article is a generalized analysis of existing methods for determining of structural steel elements behaviour in extreme conditions of subzero temperatures and their use to assess the cold resistance of steel beams ...
E. V. Kravchuk +2 more
doaj +3 more sources
Cailiao gongchengThe effect of different cold drawing deformations and annealing temperatures on the microstructure and tensile properties of Al-Si-Sc-Zr alloy wires is investigated by the mean of electron backscatter diffraction technique.
ZHENG Tao +3 more
doaj +2 more sources
Teshugang, 2017 The process for cold-drawn wire of steel 0Cr13C (/% : 0.02C, 0.32Si, 0.18Mn, 0.016P, 0.002S, 12.25Cr, 0.0140N) is φ5.5 mm hot-rolled rod annealed at 680~700°C -cold-drawing to φ2.0 mm coil-hydrogen annealing (HA) -cold-drawing to φ0.70 mm wire-HA-cold ...
宋云霞 +4 more
doaj +1 more source
Metalurgija, 2023 The aim of the conducted research works which are presented in the article was to determine the mechanical and electrical properties of Cu-Mg wires obtained in cold drawing process with total deformation at the level of 95 %.
G. Kiesiewicz +5 more
doaj +1 more source
Deformation prediction and Finite Element Analyses of precision seamless tubes during cold drawing [PDF]
MATEC Web of Conferences, 2017 This paper deals with the deformation of precision seamless tubes during the cold drawing process, using Finite Element Methods. The value of strain obtain by stereology measurement of degree grain boundaries deformation are compared with simulation ...
Necpal Martin +2 more
doaj +2 more sources
Analysis on Cold Drawing Fracture Cause of B7 Steel Rod Coil and Process Improvement
Teshugang, 2021 B7 steel Φ22 mm hot-rolled rod is fractured in cold of drawing, the fractured rod is tested by chemical composition , fractography, microstructure and energy spectrum analysis.
史杨
doaj +1 more source
Influence of Cold Drawing Strain on Torsion Properties of 304H Steel Wire
Teshugang, 2021 The influence of structure evolution and defects of 304H stainless steel wire during the cold drawing process from Φ2.6 mm to Φ0.89 mm on torsion performance of stainless steel wire are studied.
彭科, 刘静, 袁泽喜, 彭志贤
doaj +1 more source