Results 41 to 50 of about 63,948 (294)
NUMERICAL SIMULATION OF RESIDUAL STRESSES GENERATED IN THE WIRE DRAWING PROCESS FOR DIFFERENT PROCESS PARAMETERS [PDF]
Tecnologia em Metalurgia, Materiais e Mineração, 2014 The drawing process of steel bars is usually used to check better dimensional accuracy and mechanical properties to the material. In the other hand, the major concern found in manufacturing axes through this process is the appearance of distortion of ...
Juliana Zottis +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao +3 more
wiley +1 more source
Teshugang, 2007 The longitudinal crack with 0.3 mm depth occurred in φ11.5 mm cold drawn products of low carbon high sulphur free cutting structural steel (0.07C,0.86Mn,0.06P,0.32S) to product some batches of rejection.
徐芗明
doaj
, 2020 Precizno hladno deformirane cijevi proizvode se hladnim izvlačenjem i hladnim pilgerovanjem. Hladno izvlačenje cijevi provodi se na vučnoj klupi, gdje se kroz matricu određenih dimenzija izvlači cijev s većeg promjera na manji.
Tarandek, Patrik
core
Advanced Engineering Materials, EarlyView.This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley +1 more source
Influence of Cold Reduction on Structure and Properties of DQ Level Deep-Drawing Strip Steel
Teshugang, 2010 Effect of 60% - 80% cold reduction on structure, texture and mechanical properties of 1. 4 ~0. 7 mm cold rolled deep-drawing strip steel from 3. 5 mm CSP (Compact Strip Production) hot rolled plate has been studied. Results show that with increasing cold
程晓杰 +6 more
doaj
Effect of Cold Processing on the Substructure of CN-1515 Austenitic Stainless Steel Cladding Tube
Teshugang, 2023 The evolution law of substructure of CN-1515 austenitic stainless steel cladding tube after cold processing was studied by TEM （Transmission Electron Microscope） and EBSD （Electron Back-Scattered Diffraction） .
Xue Rundong, Zhao Zhiyi, Fei Aigeng
doaj
Advanced Engineering Materials, EarlyView.Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir +5 more
wiley +1 more source