Results 101 to 110 of about 5,090 (239)
Journal of Applied Polymer Science, Volume 143, Issue 41, November 5, 2026.Whole‐tire reclaimed rubber is upgraded with wood sawdust, a carpentry by‐product available at no cost, across loadings from 0 to 20 wt%. At 5 wt%, tensile strength, elongation, hardness, viscosity, and water absorption all stay within commercial specification, and real factory data show an annual production saving near $62,000 with no capital ...
Mohammed S. Matar +3 more
wiley +1 more source
Compatibilization of a polyethylene/polyamide 6 blend nanocomposite
, 2014 Polymer blends of incompatible components need to be compatibilized to give rise to a blend with good properties. At the same way, polymer/clay nanocomposites show the same problem because of different chemical nature of the polymer matrix and of the ...
M. Morreale +7 more
core +1 more source
Development of green composites based on bio-polyethylene and babassu mesocarp [PDF]
PolímerosGreen composites are sustainable alternatives to conventional materials. This study developed composites based on bio-polyethylene (Bio-PE) and babassu mesocarp (BM) (1.5 and 3 phr), using PE-grafted maleic anhydride (PE-g-MA) (3 phr) as a compatibilizer.
Crisnam Kariny da Silva Veloso +4 more
doaj +1 more source
Journal of Applied Polymer Science, Volume 143, Issue 41, November 5, 2026.Plasma treatment enhances interfacial adhesion between LDPE/PA6 via carbonyl group formation. PA6 droplet size heterogeneity reduced to ~850 nm after plasma treatment. Drawing at 160°C produces highly oriented microfibrils with faster throughput. Plasma‐treated MFCs show up to 500% tensile strength increase and 18% higher stiffness.
Narges Gray +4 more
wiley +1 more source
Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials
Advanced Engineering Materials, Volume 28, Issue 21, 4 November 2026.Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley +1 more source
Compatibilization of polymer blends
, 1995 In this paper, recent developments in compatibilization of polymer blend by means of either an addition, or in-situ formation of copolymers, are reviewed from both the theoretical and experiemental points of view.The publication is stored in the NRC ...
Utracki, L. A., Ajji, Abdellah
core
On The Viability Of Semi-Compatibilism
Ideas y Valores, 2009 Semi-compatibilism regarding responsibility is the position according to which determinism is compatible with moral responsibility quite apart from whether determinism rules out the sort of freedom that involves access to alternative possibilities. I motivate the view that whether or not semi-compatiblism is viable turns on whether various prima facie ...
openaire +4 more sources
Polymer Engineering &Science, Volume 66, Issue 11, Page 8022-8034, November 2026.Schematic representation of the fabrication of thermoplastic composites using reused post‐consumer denim fabric and PLA and PP matrices via hot press molding. ABSTRACT The increasing generation of textile waste and the growing demand for sustainable materials have made the development of polymer composites reinforced with reused post‐consumer textiles ...
Umit Koc +3 more
wiley +1 more source
Compatibilization of Polymer Blends: Micro and Nano Scale Phase Morphologies, Interphase Characterization and Properties offers a comprehensive approach to the use of compatibilizers in polymer blends, examining both fundamental and advanced knowledge in
Thomas, Sabu,editor. +1 more
core
, 2014 International audienceUnderstanding of the compatibilization effect of the multifunctionalized epoxy in PLA/PBAT biopolymer blends: linear and non-linear rheology, morphology and interfacial ...
Al-Itry, Racha +2 more
core +4 more sources