Results 211 to 220 of about 79,385 (264)

Trisferrocenyltrithiophosphite-Copper(I) Bromide Composites for Electrochemical CO₂ Reduction. [PDF]

Int J Mol Sci
Khrizanforov M, Bezkishko I, Samorodnova A, Shekurov R, Gainullin R, Kholin K, Yanilkin I, Gubaidullin A, Galushko A, Miluykov V.   +9 more
europepmc   +1 more source

Manganese (Mn) doping effects on the structure and surface characteristics of copper zinc tin sulphide (CZTS) transition metal sulphides synthesised <i>via</i> a sol-gel method. [PDF]

RSC Adv
Najitha AR, Che Balian SR, Ahmoum H, Omar FS, Chelvanathan P, Su'ait MS.   +5 more
europepmc   +1 more source

Some of the next articles are maybe not open access.

Related searches:

Flowability of Electrolytic Copper Powder

Materials Science Forum, 2005
The surface structure of powder particles, which allows free flow of copper powder, was examined. It has been shown that a sufficiently dense surface structure which permits free flow will be obtained if apparent density is higher than 2.2 – 2.3 g/cm3.
Pavlović, Miomir, Popov, Konstantin I., Krstić, Snežana B., Pavlovic, LJ, Ivanović, Evica   +4 more
openaire   +3 more sources

Atomized copper powders

Soviet Powder Metallurgy and Metal Ceramics, 1981
For the first time in the Soviet Union pilot-plant batches of copper powder have been produced by the method of atomization of melts with water under high pressure. The powder produced is characterized by increased apparent density and flowability. The best compressibility (2–6 tons/cm2) is exhibited by the powder after annealing.
A. N. Karibyan, A. B. Medvedovskii, V. A. Belyakov, N. S. Sarkisyan, N. G. Dyuzhakova, O. S. Nichiporenko, V. T. Aivazyan, V. P. Poteshkina, Yu. I. Naida   +8 more
openaire   +1 more source

Vibration Cladding of Copper Powder with Aluminum

Inorganic Materials: Applied Research, 2019
This paper proposes a method for rapid cladding of copper powder with aluminum. The optimal parameters (frequency and amplitude of oscillations) of the experimental setup and the dispersity and volume fraction of the interacting powders are determined. The most productive cladding mechanism is considered. Dependences of the coating thickness (from 5 to
Yu.V. Kontsevoi, A.G. Meilakh
openaire   +1 more source

Fine Copper Powders Production

Defect and Diffusion Forum, 2021
The article is devoted to the description of a method for producing electrolytic copper powder with an average particle size of 3 to 10 μm. In order to increase the proportion of the finely dispersed fraction during the electrolysis process, the composition of the electrolyte was changed. In particular, the content of chloride ions was increased from 6
Natalia E. Agarova, Lyubov M. Yakovleva, Roman S. Voinkov, Konstantin L. Timofeev   +3 more
openaire   +1 more source

Production of Copper and Copper Alloy Powders

2015
Abstract This article describes the fundamentals of various techniques used for the production of copper and copper alloy powders. These include atomization (water, air, and gas), oxide reduction, and electrolysis. The article discusses the effects of electrolyte composition and operating conditions on the characteristics of copper and ...
Thomas W. Pelletiers, Wayne K. Daye
openaire   +1 more source

The Effect of Reversing Current on the Properties of Copper and Electrolytic Copper Powder. I. The Morphology of Powder Particles

Materials Science Forum, 2004
The selective dissolution of copper dendrites during electrodeposition by reversing current was discussed and the effects on the morphology of copper powder particles were elucidated.
Pavlović, MG, Popov, Konstantin I., Pavlović, Ljubica, Ivanović, Evica, Jović, VD   +4 more
openaire   +2 more sources

Reactions of Ethyl Bromodifluoroacetate in the Presence of Copper Powder

ChemInform, 2004
AbstractFor Abstract see ChemInform Abstract in Full Text.
Kazuyuki Sato, Masaaki Omote, Akira Ando, Itsumaro Kumadaki   +3 more
openaire   +1 more source