Results 81 to 90 of about 79,385 (264)
Case Studies in Thermal EngineeringNarrow gap channel boiling heat transfer is considered one of the most promising cooling technologies for addressing high heat flux dissipation problems.
Qiushi Gu +3 more
doaj +1 more source
Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion
Advanced Engineering Materials, EarlyView.Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello +7 more
wiley +1 more source
A Dislocation Perspective on Strength and Toughness in Ceramics
Advanced Engineering Materials, EarlyView.Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley +1 more source
On the Fracture of Copper Powder Compacts
Journal of the Japan Society of Powder and Powder Metallurgy, 1975 Fracture behaviour of green compacts is investigated under an axi-symmetrical stress condition such that σ2=σ3 in three principal stresses σ1, σ2 and σ3, that is, a uniaxial compression and a compression under hydrostatic pressure.Relations between σ1 and σ2 at fracture point, and between σ2 and fracture strain e1f are investigated. The former relation
Okimoto, Kunio +2 more
openaire +2 more sources
Lithium-ion attack on yttrium oxide in the presence of copper powder during Li plating in a super-concentrated electrolyte. [PDF]
RSC Adv, 2021 Shiga T, Masuoka Y, Nozaki H, Ohba N.
europepmc +1 more source
Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application
Advanced Engineering Materials, EarlyView.N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition
Advanced Engineering Materials, EarlyView.AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley +1 more source
Enhancing Low‐Temperature Performance of Sodium‐Ion Batteries via Anion‐Solvent Interactions
Advanced Functional Materials, EarlyView.DOL is introduced into electrolytes as a co‐solvent, increasing slat solubility, ion conductivity, and the de‐solvent process, and forming an anion‐rich solvent shell due to its high interaction with anion. With the above virtues, the batteries using this electrolyte exhibit excellent cycling stability at low temperatures. Abstract Sodium‐ion batteries
Cheng Zheng +7 more
wiley +1 more source