Results 111 to 120 of about 338,910 (262)
Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials
Advanced Engineering Materials, EarlyView.Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai +2 more
wiley +1 more source
Near-Coulomb-barrier Fusion of 16,18O+52Cr Systems
Yuanzineng kexue jishuNear-Coulomb-barrier (near-barrier) fusion of heavy-ions is a complicated reaction process which is related to the quantum tunneling and coupled-channels effect as well as the synthesization of super-heavy elements.
DUAN Hairui1, JIA Huiming1, LIN Chengjian1, 2, WEN Peiwei1, YANG Lei1, MA Nanru1, YANG Feng1, LUO Tianpeng1, ZHANG Huanqiao1
doaj +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
, 2012 Despite the supposed simplicity of double-closed shell nuclei, conventional coupled-channels calculations, that include all of the known collective states of the target and projectile, give a poor fit to the fusion cross section for the $^{16}$O + $^{208}
D. Agassi +5 more
core +3 more sources
Packaging of Macroscopic Material Payloads: Needs, Challenges, Concepts, and Future Directions
Advanced Engineering Materials, EarlyView.This review introduces a unified framework that decomposes any macroscopic packaging system into the payload, packaging material, and packaging strategy and combines them into a conceptual packaging equation: packaging strategy = payload + packaging material.
Venkata S. R. Jampani, Manos Anyfantakis
wiley +1 more source
Recent developments in heavy-ion fusion reactions around the Coulomb barrier
EPJ Web of Conferences, 2016 The nuclear fusion is a reaction to form a compound nucleus. It plays an important role in several circumstances in nuclear physics as well as in nuclear astrophysics, such as synthesis of superheavy elements and nucleosynthesis in stars. Here we discuss
Hagino K., Rowley N., Yao J.M.
doaj +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Inelastic neutron scattering cross-section measurements on 7Li and 63,65Cu
EPJ Web of Conferences, 2017 The γ-ray production cross section for the 477.6-keV transition in 7Li following inelastic neutron scattering has been measured from the reaction threshold up to 18 MeV.
Nyman Markus +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source