Results 51 to 60 of about 3,388 (296)
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
Mechanically-assisted crevice corrosion and its effect on materials degradation
Corrosion Communications, 2023 Mechanically-assisted crevice corrosion (MACC) is a synergistic combination of wear and crevice corrosion. The major differences between tribocorrosion, fretting corrosion and MACC relate to the relative scale of motion and contact area, are clarified in
Weichen Xu +5 more
doaj +1 more source
Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A
Advanced Engineering Materials, EarlyView.The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han +5 more
wiley +1 more source
Mapping the concentration changes during the dynamic processes of crevice corrosion by digital [PDF]
Journal of the Serbian Chemical Society, 2009 The dynamic process of crevice corrosion during anodic dissolution of a crevice electrode in a 5.0 mmol dm-3 NaCl solution has been studied by digital holographic reconstruction.
HENGLEI JIA +4 more
doaj
Journal of Materials Research and Technology, 2022 The deep-sea field exposure experiment of 5A06 aluminum alloy was carried out successfully in the South China Sea with the sea depths of 1200 m, 2000 m, and 3000 m for one year.
Tigang Duan +6 more
doaj +1 more source
Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying
Advanced Engineering Materials, EarlyView.An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara +8 more
wiley +1 more source
Simulation of Crevice and Pitting Corrosion Using the Orthogonal Collocation Method
Journal of King Saud University: Engineering Sciences, 1996 Two dangerous forms of localized corrosion are pitting and crevice corrosion. In pitting corrosion, pits are formed as a result of differences in oxygen and ion concentration at the base of a pit compared with the surface.
A.M. Abu-Khalaf +2 more
doaj +1 more source
Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment
Advanced Engineering Materials, EarlyView.This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li +5 more
wiley +1 more source
, 2011 Silver – silver chloride electrodes (Ag/AgCl) for the detection of chloride ions were fabricated using thick-film technology. Five different formulations were prepared and chloride responses were investigated over time.
Wood, R.J. K +11 more
core +1 more source
Advanced Engineering Materials, EarlyView.Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir +5 more
wiley +1 more source