Results 81 to 90 of about 667,778 (340)
Challenges during Flash Lamp Annealing of Aerosol‐Deposited Barium Titanate Films
Aerosol deposition is used to rapidly deposit barium titanate films with thicknesses ranging from 2 to 16 μm at room temperature, eliminating the need for further densification. However, to recover the electromechanical properties, annealing is required, which limits the usage of temperature‐sensitive substrates.
Michel Kuhfuß +7 more
wiley +1 more source
Strain Rate Induced Crystallization in Bulk Metallic Glass-Forming Liquid [PDF]
We report on the solidification of Au49Ag5.5Pd2.3Cu26.9Si16.3 bulk metallic glass under various strain rates. Using a copper mold casting technique with a low strain rate during solidification, this alloy is capable of forming glassy rods of at least 5 ...
Johnson, William L. +2 more
core +1 more source
Mechanically Deposited Wear‐Resistant Amorphous Zr55Cu30Al10Ni5 Coatings
Mechanically deposited from glassy ribbons, the Zr55Cu30Al10Ni5 amorphous coating formed a hard, continuous layer on AISI 1010 steel, tripling substrate hardness, lowering friction, and reducing wear. Despite its rough surface, it showed friction and wear behavior comparable to the crystalline alloy, highlighting its strong potential as a durable ...
Tales Ferreira +8 more
wiley +1 more source
Crystal Growth of Single Salicylamide Crystals [PDF]
Growth of single salicylamide crystals was investigated in a nonstirred growth cuvette and on a rotating disk. In the growth cuvette the crystal growth rates were measured for both primary nucleated crystals and seed crystals manually inserted into the cuvette.
Lynch Aisling, Rasmuson Åke
openaire +1 more source
Triphasic BiFeO3–PbZr0.58Ti0.42O3–MnFe2O4 composites exhibit enhanced ferroelectric and magnetic behavior, achieving 70.76% energy‐storage efficiency and improved polarization switching. The coupling between ferroelectric and magnetic phases enables multifunctional performance, making these composites promising candidates for next‐generation energy ...
Hassan Raza Khan +7 more
wiley +1 more source
Fines Formation (and Prevention) in Seeded Precipitation Processes
An overview of three studies on seeded precipitation in a fluidised bed reactor (FBR) is presented. The objective of using the FBR is to remove dissolved metals as precipitated metal salts onto a seed surface.
Alison Lewis
doaj +1 more source
Isothermal Crystallization Kinetics of Poly(lactic acid) Stereocomplex/Graphene Nanocomposites [PDF]
The isothermal crystallization kinetics of PLA stereocomplex (scPLA) and scPLA/graphene oxide nanocomposites was investigated. scPLA was prepared by symmetric blending the two isomers, PLLA and PDLA and the scPLA nanocomposite by polymerization of the ...
Diego H. S. Souza +2 more
doaj +1 more source
Crystallization of Isotactic Poly(methylmethacrylate) in Monolayers and Thin Films [PDF]
Langmuir-Blodgett monolayers of isotactic PMMA exhibit a pressure-induced transition upon compression, that can be described in terms of a two-dimensional crystallization process, analogous to a normal melt crystallization.
Brinkhuis, R.H.G.,, Schouten, A.J.,
core +1 more source
Surface crystallization of ionic liquid crystals [PDF]
The [C12mim][BF4] surface was characterized showing an ordered layer and solid-like behavior, supporting the hypothesis of a surface freezing phenomenon.
Mónia A. R. Martins +10 more
openaire +3 more sources
A high‐performance n‐type element for quasi‐solid‐state thermocells has been introduced, outperforming conventional p‐type elements and showcasing the potential to harness body heat as an energy source or power embedded sensors. This advance significantly contributes to waste thermal energy harvesting and wearable technology, paving the way for self ...
Gilyong Shin +10 more
wiley +1 more source

