Results 121 to 130 of about 918,916 (305)

Exploiting metabolic adaptations to overcome dabrafenib treatment resistance in melanoma cells

open access: yesMolecular Oncology, EarlyView.
We show that dabrafenib‐resistant melanoma cells undergo mitochondrial remodeling, leading to elevated respiration and ROS production balanced by stronger antioxidant defenses. This altered redox state promotes survival despite mitochondrial damage but renders resistant cells highly vulnerable to ROS‐inducing compounds such as PEITC, highlighting redox
Silvia Eller   +17 more
wiley   +1 more source

Stress-Strain State and Damage of Tribo-Fatigue System Clamp-Knife-Base of Harvester Cutting Instrument

open access: yesМеханика машин, механизмов и материалов, 2012
Multicomponent clamp-knife-base system of cutting instrument of a harvester is considered. Stress-strain and damage states of the system are calculated in two-dimensional statement.
S.S. Scherbakov
doaj  

Підвищення якісних показників вставного породоруйнівного оснащення шарошок тришарошкових бурових доліт [PDF]

open access: yes, 2013
Дослідження має на меті вирішення проблеми підвищення якісних показників вставного породоруйнівного оснащення шарошок тришарошкових бурових доліт. Дослідження проводились в умовах реального виробництва бурових доліт, за умов математичного планування ...
Петрина, Ю. Д.   +2 more
core  

TREX1, a predator for treating MSI‐H tumors?

open access: yesMolecular Oncology, EarlyView.
Immunotherapy benefits many patients; yet, some with MSI‐H tumors remain unresponsive despite their high immunogenicity. Xu et al. reveal that TREX1 enables immune evasion by degrading cytosolic DNA and suppressing cGAS–STING–IFN‐I signaling. TREX1 loss restores DNA sensing, increases CD8+ T and NK cell infiltration, and boosts antitumor immunity ...
Elena Benidovskaya   +2 more
wiley   +1 more source

Improvement of face mill design for finishing flat surface parts

open access: yesТехнічна інженерія
The quality machined surface parts depends on the kinematics cutting process, the processing mode, structural and geometric parameters of the cutting tool, etc.
H.M. Vyhovskyi   +3 more
doaj   +1 more source

ATF4‐mediated stress response as a therapeutic vulnerability in chordoma

open access: yesMolecular Oncology, EarlyView.
We screened 5 chordoma cell lines against 100+ inhibitors of epigenetic and metabolic pathways and kinases and identified halofuginone, a tRNA synthetase inhibitor. Mechanistically halofuginone induces an integrated stress response, with eIF2alpha phosphorylation, activation of ATF4 and its target genes CHOP, ASNS, INHBE leading to cell death ...
Lucia Cottone   +11 more
wiley   +1 more source

Developing evidence‐based, cost‐effective P4 cancer medicine for driving innovation in prevention, therapeutics, patient care and reducing healthcare inequalities

open access: yesMolecular Oncology, EarlyView.
The cancer problem is increasing globally with projections up to the year 2050 showing unfavourable outcomes in terms of incidence and cancer‐related deaths. The main challenges are prevention, improved therapeutics resulting in increased cure rates and enhanced health‐related quality of life.
Ulrik Ringborg   +43 more
wiley   +1 more source

New types of drilling tools fit with PCD elements [PDF]

open access: yes, 1997
One of the most significant developments in drilling technology over the last years has been the introduction of polycrystalline diamond (PCD) as macro-cutting elements in the rotary drill application.
Koníèek Jiøí   +2 more
core  

Cell surface interactome analysis identifies TSPAN4 as a negative regulator of PD‐L1 in melanoma

open access: yesMolecular Oncology, EarlyView.
Using cell surface proximity biotinylation, we identified tetraspanin TSPAN4 within the PD‐L1 interactome of melanoma cells. TSPAN4 negatively regulates PD‐L1 expression and lateral mobility by limiting its interaction with CMTM6 and promoting PD‐L1 degradation.
Guus A. Franken   +7 more
wiley   +1 more source

Влияние величины переднего и заднего угла спирального сверла на силу резания при сверлении отверстий в литейных алюминиях [PDF]

open access: yes, 2003
In the article there giver the results of investigations about the determining the effect of quantity of front and back angles standard spiral drill with elements of grinding cut on cutting force and friction force at drilling deep holes in casting ...
Маршуба, Вячеслав Павлович
core  

Home - About - Disclaimer - Privacy