Results 101 to 110 of about 89,685 (265)

Research on the Method of Reducing Dynamic Cutting Force in Aspheric Machining. [PDF]

Micromachines (Basel), 2023
Zhuang G, Liu H, Zong W.
europepmc   +1 more source

Laser Powder Bed Fusion of Copper–Tungsten Composites for Heat Sink Applications in High‐Power Electronics

Advanced Engineering Materials, EarlyView.
This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh, Shashank Deepak Prabhu, Jannik Huber, Lioba Fischer, Gerhard Wolf, Nico Hempel, Peter Mayr   +6 more
wiley   +1 more source

Cutting-Force Modeling Study on Vibration-Assisted Micro-Milling of Bone Materials. [PDF]

Micromachines (Basel), 2023
Shang P, Zhang H, Liu X, Yang Z, Liu B, Liu T.   +5 more
europepmc   +1 more source

Effects of Carbon Nanoparticles on Triboelectro‐Induced Surface Defects

Advanced Engineering Materials, EarlyView.
Carbon nanoparticles added to grease modify the electrocontact behavior. The synergy of particle concentration and electric current dominates the surface damage of metals in contact. Electrical surface damage caused by current leakage is a critical challenge in high‐performance applications such as electric vehicle (EV) drivetrains and wind turbine ...
Mohsen Tajedini, Lu Fang, Jacob Bons, Mohammad Humaun Kabir, Evan Johnson, Joe Kosmoski, Hong Liang   +6 more
wiley   +1 more source

Effect of Duty Cycle on Cutting Force for Ultrasonic Vibration-Assisted Milling Carbon Fiber-Reinforced Polymer Laminates. [PDF]

Materials (Basel), 2023
Zhang Y, Ren J, Zhou J.
europepmc   +1 more source

Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution

Advanced Engineering Materials, EarlyView.
Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat, Hamidreza Enshaei, Elaine Armelin, José I. Iribarren, Antonio Mateo, Miguel Morales   +5 more
wiley   +1 more source

Experimental Study on the Influence of Wire-Saw Wear on Cutting Force and Silicon Wafer Surface. [PDF]

Materials (Basel), 2023
Liang L, Li S, Lan K, Yu R, Wang J, Zhao W.   +5 more
europepmc   +1 more source

Interactions between Molten High‐Silicon Electrical Steels and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert, Matheus Roberto Bellé, Anton Yehorov, Anhelina Mospan, Till M. J. Stadtmüller, Seetharaman Sridhar, Christos G. Aneziris, Olena Volkova   +7 more
wiley   +1 more source

Compressible Flow Exfoliation of Two‐Dimensional Nanomaterials: Insights Into Layer Separation Informed by Gas Dynamics

Advanced Engineering Materials, EarlyView.
This study elucidates the mechanism of compressible flow exfoliation for producing 2D hexagonal boron nitride (h‐BN). Fluid dynamics analysis reveals that acceleration‐driven aerodynamic shear forces, rather than shock waves alone, drive effective layer separation.
Md Farhadul Islam, Saeed Arabha, Ray Hixon, Reza Rizvi   +3 more
wiley   +1 more source

Fixed-Diamond Abrasive Wire-Saw Cutting Force Modeling Based on Changes in Contact Arc Lengths. [PDF]

Micromachines (Basel), 2023
Liang L, Li S, Lan K, Wang J, Yu R.
europepmc   +1 more source