Results 201 to 210 of about 3,517,652 (393)

Microstructural Evolution and Mechanical Performance of Plasma‐Assisted Hybrid Friction Stir Welded Dissimilar Aluminum–Copper Joints

Advanced Engineering Materials, EarlyView.
Plasma‐assisted hybrid friction stir welding of dissimilar AlCu joints employs localized plasma preheating to balance heat input and enhance plastic flow. The optimized process reduces axial force by up to 35%, refines the microstructure, and achieves ≈96% joint efficiency.
Deepak Kumar Yaduwanshi, Pankaj Shrivastava, Ganesh Chouhan, Velaphi Msomi   +3 more
wiley   +1 more source

Methodology for Evaluating the Cutting Force of Planar Technical Blades Used in Flatfish Processing. [PDF]

Micromachines (Basel), 2021
Zieliński B, Chaciński T, Pimenov DY, Nadolny K.   +3 more
europepmc   +1 more source

Thrust Force Directional Vibration-Assisted Cutting Based on a Removal Process of Ductile-Mode Grinding

, 2020
Yuta OSANAI, Kenichiro Imai
openalex   +2 more sources

Enhancing Fatigue Performance by Tuning of Residual Stresses in Welded Joints through Nanometallic Multilayer

Advanced Engineering Materials, EarlyView.
This study investigates the fundamental mechanisms of a novel postweld treatment that significantly enhances fatigue performance through engineered residual stress (RS) states. A multiscale approach correlates tensile RS in the nanometallic multilayer coating with corresponding compressive RS in the steel substrate, thereby reducing localized stress ...
Niclas Spalek, Guilherme Abreu Faria, Anton Davydok, Marcus Rutner   +3 more
wiley   +1 more source

THEORETICAL ANALYTICAL METHOD OF CUTTING FORCES IN TURNING OF Al/Si C COMPOSITES BASED ON THREE DEFORMATION AREA

Jixie qiangdu, 2018
To predict the cutting force of cutting Si C particle reinforced aluminum-based compositeaccurately,an innovative theoreticalanalytical method is proposed in consideration of the influence of Si C particles on aluminum substrate.
PENG ChunLei
doaj  

Design and Development of a Tri-Axial Turning Dynamometer Utilizing Cross-Beam Type Force Transducer for Fine-Turning Cutting Force Measurement. [PDF]

Sensors (Basel), 2022
Rizal M, Ghani JA, Mubarak AZ.
europepmc   +1 more source

Frequency-Based Analysis of the Relationship between Cutting Force and CT Number for an Implant-Surgery-Teaching Robot

, 2016
Koyo Yu, Takuya Matsunaga, Hiromasa Kawana, Shin Usuda, Kouhei Ohnishi   +4 more
openalex   +2 more sources

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Studies on the chip control in metal cutting. (3rd report). Influence of chip breaker on cutting force and chip controllability.

, 1988
Yoshiki Chujo, Toshio HARA, Masahiro Masuda   +2 more
openalex   +2 more sources

3D Bioprinting of Thick Adipose Tissues with Integrated Vascular Hierarchies

Advanced Functional Materials, Volume 35, Issue 12, March 18, 2025.
An advanced 3D bioprinting technique is used here to create thick adipose tissues with a central, vessel and extensive branching. The construct is made using alginate, gelatin and collagen‐based bioinks. Flow through the complex vessel network is demonstrated as well as its successful integration with a femoral artery following implantation in a rat ...
Idit Goldfracht, Majd Machour, Inbal Michael, Maria Bulatova, Janette Zavin, Shulamit Levenberg   +5 more
wiley   +1 more source