Results 31 to 40 of about 3,186,442 (250)
Applied Sciences, 2021 The friction behavior in the tool-chip interface is an essential issue in aluminum matrix composite material (AMCM) turning operations. Compared with conventional cutting, the elliptical vibration (EVC) cutting AMCM has attractive advantages, such as low
Yucheng Li, Xu Zhang, Cui Wang
doaj +1 more source
Nonlinear Dynamic Analysis of the Cutting Process of a Nonextensible Composite Boring Bar
Shock and Vibration, 2020 A nonlinear dynamic analysis of the cutting process of a nonextensible composite cutting bar is presented. The cutting bar is simplified as a cantilever with plane bending.
Bole Ma, Yongsheng Ren
doaj +1 more source
Modelling stem cell differentiation related processes—A practical overview for biologists
FEBS Letters, EarlyView.Stem cell differentiation is complex and difficult to control experimentally. This review introduces suitable computational modelling approaches that can support stem cell research, from mechanistic ODE and abstract models to multiscale and deep learning methods.
Ricco Zeegelaar +4 more
wiley +1 more source
Design and analysis of a piezoelectric film embedded smart cutting tool [PDF]
, 2013 This is the author's accepted manuscript. The final published article is available from the link below. Copyright @ 2012 Institution of Mechanical Engineers.The condition of a cutting tool is an important factor for manufacturing processes.
Cheng, K, Rakowski, R
core +1 more source
Micromachines, 2022 The single-point diamond-turning operation is a commonly used method for ultra-precision machining of various non-ferrous materials. In this paper, a magnetic field was introduced into a single-point diamond-turning system, and magnetic-field-assisted ...
Xian Wu +7 more
doaj +1 more source
Ligand‐dependent transcriptional heterogeneity in cell cycle gene expression delays G1/S entry
FEBS Letters, EarlyView.EGF and HRG induce distinct G1/S progression programs in ErbB2‐amplified BT474 breast cancer cells. Despite activating the potent ErbB2–ErbB3 heterodimer, HRG does not accelerate cell‐cycle entry. Instead, EGF promotes earlier restriction‐point passage via ERK–FOS signaling, whereas HRG activates the AKT–MYC axis, driving transcriptional heterogeneity ...
Ririn Rahmala Febri +5 more
wiley +1 more source
SPH method applied to high speed cutting modelling [PDF]
, 2007 The purpose of this study is to introduce a new approach of high speed cutting numerical modelling. A Lagrangian smoothed particle hydrodynamics (SPH)- based model is arried out using the Ls-Dyna software.
J. Limido +9 more
core +1 more source
An expert mill cutter and cutting parameters selection system incorporating a control strategy [PDF]
, 2008 This paper discusses the selection of tools and cutting parameters in milling operations. To carry out this research, an expert system has been developed based on numerical methods of performance evaluation.
De la Sen Parte, Manuel +1 more
core +4 more sources
FEBS Letters, EarlyView.How do genomes gain new functional parts? In eukaryotes, which tend to evolve under weak selection, much of the genome is junk. Palazzo and Qiu borrow the logic of Markov chains to show how non‐functional DNA becomes functional through the appearance of intermediate states, which arise due to epistasis, buffering, and biochemical messiness, allowing ...
Alexander F. Palazzo, Yi Qiu
wiley +1 more source
Experimental study of the brittle–ductile transition in hot cutting of SG iron specimens [PDF]
, 2013 http://www.sciencedirect.com/science/article/pii/S0924013612002579The present paper investigates the brittle-ductile transition (BDT) of the primary shear zone during cutting of spheroidal graphite (SG) iron in the austenitization temperature range ...
EL MANSORI, Mohamed +2 more
core +1 more source