Results 11 to 20 of about 332,414 (335)
Nuclear Engineering and Technology, 2017 Influences of hold time and stress ratio on cyclic creep properties of Grade 91 steel were systemically investigated using a wide range of cyclic creep tests, which were performed with hold times (HTs) of 1 minute, 3 minutes, 5 minutes, 10 minutes, 20 ...
Woo-Gon Kim +4 more
doaj +4 more sources
Nonlinear shear mass participation factor (rd) for cyclic shear stress ratio evaluation
Soil Dynamics and Earthquake Engineering, 2004 Most methods for assessment of in situ seismic soil liquefaction potential require evaluation of the earthquake-induced cyclic shear stress ratio (CSR). Estimates of the in situ CSR can be developed directly, using dynamic response analyses, but it is common in ‘simplified’ analysis methods to develop estimates of the in situ CSR using empirical ...
K.Onder Cetin, Raymond B. Seed
exaly +5 more sources
Environmental Challenges, 2023 Civil Engineering structures are constantly subjected to environmental forces and changes around the surroundings hence a strong need for assessment of the interaction and predictive measures that lead to pro-active actions towards the structural safety ...
Aman Pawar +5 more
doaj +3 more sources
Cyclic compression of sands at constant stress ratio—experimental investigations and constitutive modelling [PDF]
Acta Geotechnica, 2022 AbstractSeveral constitutive models for sands are based on an additive split of the effective stress rate into two terms. One term accounts for the deviatoric stress ratio $$\varvec{r}$$ r , the other for the mean effective stress $${p}$$ p ...
Christian Carow, Frank Rackwitz
openaire +3 more sources
TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series A, 1981 Influences of stress ratios and stress cycle frequencies on cyclic stress corrosion crack growth characteristics of a high-strength steel have been investigated. The influences of stress ratios on crack growth rate under cyclic SCC are clearly distinguished between above and below KISCC. In the range of Kmax, KFSCC≤ Kmax < KISCC, a decrease of R causes
Kichiro ENDO +2 more
+6 more sources
Cyclic stress-controlled tests on offshore clay
Journal of Rock Mechanics and Geotechnical Engineering, 2017 One of the main concerns in cyclic behavior of soft clay is gradual degradation with the progression of loading cycle. A series of cyclic constant-volume direct simple shear (CDSS) loading tests was performed on Malaysia offshore clay to study its ...
S.Y. Thian, C.Y. Lee
doaj +3 more sources
Including the normal to shear stresses ratio in fatigue life estimation for cyclic loadings [PDF]
MATEC Web of Conferences, 2019 The paper presents the estimation of the fatigue life under multiaxial cyclic loading of two construction materials. The main aim of this paper is to present a new method which allows evaluation of fatigue life during the design and construction phase of machine elements. In paper three well known multiaxial fatigue criteria based on the critical plane
Marta Kurek
openaire +3 more sources
Computers and Geotechnics, 2023 Various constitutive formulations have been developed over the years to reproduce the cyclic resistance of sands. A common challenge for existing models is the accurate simulation of the cyclic strength of sands for a wide range of initial conditions and different cyclic stress levels when adopting a single calibration. Many liquefaction models tend to
J.K. Möller +3 more
openaire +3 more sources
International Journal of FatiguePresented test results on transverse cracking in cross-ply laminates upon tension–tension cyclic loading show that the increase of crack density depends not only on the maximum transverse stress in the cycle but also on the local cyclic stress ratio RTloc in the analyzed layer.
Vivek Richards Pakkam Gabriel +3 more
+6 more sources
Yantu gongcheng xuebao, 2023 A series of temperature-controlled triaxial tests are conducted on the deep-sea sediment from the Western trough of the South China Sea. The undrained heating effects on undrained shear strength, pore pressure and critical cyclic stress ratio are ...
SUN Anyuan 1, YANG Gang 1, REN Yubin 1, KONG Gangqiang 2, YANG Qing 1
doaj +2 more sources