Results 51 to 60 of about 1,108 (185)
Chemical Biology &Drug Design, Volume 108, Issue 1, July 2026.Structure‐guided and biochemical analyses indicate that DNA primase of Leishmania donovani represents a potential therapeutic target, as repurposed compounds, particularly Pritelivir, demonstrate marked inhibitory effects accompanied by reduced parasite proliferation, replication, and altered cellular morphology in in vitro and cell‐based studies ...
Deep Bhowmik +3 more
wiley +1 more source
Journal of the American Ceramic Society, Volume 109, Issue 7, July 2026.ABSTRACT The co‐sintering of kaolinite with varying contents of jadeite‐type (Jd) glass yields mullite‐containing glass‐ceramic composites with tunable properties, offering fine control over the crystallizing phases and residual glass content. The Jd glass phase drastically decreases the sintering temperature by instigating a liquid phase sintering ...
Guilherme N. B. M. de Macedo +2 more
wiley +1 more source
Advanced Materials Technologies, Volume 11, Issue 12, 18 June 2026.This study formulated a 5Y‐PSZ zirconia paste for extrusion‐based additive manufacturing via direct ink writing, producing dense ceramic structures for dental applications. A colloidal approach with 47 vol% nanometric powder and tailored additives optimized rheology and printability.
Juliana de Freitas Gouveia Silva +5 more
wiley +1 more source
3D‐Printed Na3V2(PO4)3 Electrodes for Symmetric Sodium‐Ion Batteries
Small Structures, Volume 7, Issue 6, June 2026.Vat photopolymerization 3D printing is used to fabricate current collector‐free Na3V2(PO4)3 (NVP) electrodes with complex lattice geometries. After thermal postprocessing, the printed electrodes operate reversibly as both positive and negative electrodes in a symmetric sodium‐ion battery.
Ana C. Martinez +12 more
wiley +1 more source
Virtual and Physical PrototypingMaterial extrusion (ME) based additive manufacturing has gained much attention as a cost-effective method for the fabrication of complex metal components, particularly using 17-4PH stainless steel.
Yulin Liu, Audai Al-Akailah, Fuda Ning
doaj +1 more source
International Journal of Applied Ceramic Technology, Volume 23, Issue 3, June 2026.The article describes a methodology to obtain spatial map of full piezoelectric tensor of an architected polycrystalline piezoceramic, based on direct knowledge of microstructural changes that is gained through in situ X‐ray microdiffraction and further complemented by micromechanical computations.
Abhijit Pramanick +7 more
wiley +1 more source
International Journal of Applied Ceramic Technology, Volume 23, Issue 3, June 2026.Silicon nitride samples were slip cast using ytterbium oxide sintering aids to fabricate porous materials for radar frequency windows. Varying sintering temperature and ytterbium oxide content were used to tailor microstructure and phase composition. Flexural strength was measured at room temperature and 1000°C.
Averyonna R. Kimery +5 more
wiley +1 more source
Debinding and sintering solutions for metals and ceramics
Metal Powder Report, 2001 Abstract Proper removal of organic binders and lubricants is critical if the required properties are to be attained in sintered metal and ceramic parts. Scott K. Robinson and Matthew R. Paul of Centorr/Vacuum Industries (Nashua, NH, USA) consider the issues involved in debinding different materials, and detail the design and operation of various ...
Scott K. Robinson, Matthew R. Paul
openaire +1 more source
Fabrication of tungsten heavy alloy long rods by warm powder extrusion and vacuum sintering
Journal of Materials Research and Technology, 2019 The long rods of tungsten heavy alloy (WHA) which contain W–5Ni–1.5Fe (wt.%) were fabricated by using warm powder extrusion. The elemental powders were first mixed, and then the mixture was prepared for warm back extrusion by adding a proper binder at 5 ...
Mai Essam +3 more
doaj +1 more source
Journal of the Japan Society of Powder and Powder Metallurgy, 1996 Shimizu, Toru +3 more
openaire +3 more sources