Results 1 to 10 of about 448,207 (186)
Journal of Materials Research and TechnologyAn environment-friendly solvent debinding process for polyoxymethylene (POM) for metal injection molding (MIM) is presented as an alternative to the traditional catalytic debinding method.
Keemi Lim +6 more
doaj +5 more sources
Solvent debinding and critical thickness of ultrafine cemented carbides by prepared injection molding [PDF]
Fenmo yejin jishu, 2023 Ultrafine cemented carbides with the different thickness were prepared by metal powder injection molding, using WC–10Co with the particle sizes of 0.71 μm and 0.53 μm as the raw materials and the wax-based binder system as the binders.
LUO Xuequan, LIU Sunhe, WEN Guanghua
doaj +3 more sources
Rheological property and solvent debinding behavior of microcrystalline wax based feedstocks for injection molding [PDF]
Fenmo yejin jishu, 2022 Microcrystalline wax was mixed with the WC–10Co (YG10) powders to obtain the injection molding feedstocks as the main component of the binders. The non-Newtonian index, viscous flow activation energy, and synthetic rheological factor of the feedstocks ...
YUAN Jian-kun +3 more
doaj +3 more sources
Effects of Solvent Debinding on the Microstructure and Properties of 3D-Printed Alumina Ceramics [PDF]
ACS Omega, 2020 Solvents assist in the debinding of stereolithography-based 3D-printed alumina green bodies. The green bodies subsequently undergo thermal debinding and sintering to obtain alumina ceramics. In this study, several solvents were tested, including polyethylene glycol, oxalic acid, ammonium hydroxide, ethyl alcohol, methyl methacrylate, butyl acetate ...
He Li +5 more
doaj +5 more sources
Virtual and Physical PrototypingMaterial extrusion (ME) based additive manufacturing has gained much attention as a cost-effective method for the fabrication of complex metal components, particularly using 17-4PH stainless steel.
Yulin Liu, Audai Al-Akailah, Fuda Ning
doaj +3 more sources
Characterization of FeCoV alloy processed by PIM/MIM route [PDF]
Science of Sintering, 2017 In this study the characterization of FeCo-2V alloys toroidal samples produced by PIM/MIM technology was presented. The feedstock for metal injection molding (MIM) was prepared by mixing starting FeCoV powder with a low viscosity binder.
Nedeljković Borivoje +4 more
doaj +1 more source
Influence of Solvent Type, Specimen Dimensions and Temperature on Chemical Debinding of Alumina Parts Fabricated Via Digital Light Processing [PDF]
Materials ResearchVat photopolymerization via digital light processing (DLP) enables the rapid fabrication of high-resolution ceramic components. However, careful post-processing is required to remove the hardened resin and consolidate the microstructure.
J. P. F. Matheus, A.P. Luz
doaj +1 more source
Journal of Magnesium and Alloys, 2023 In this study, a binder based 3D-printing technology viz. Fused Granular Fabrication (FGF) technique was used to produce interconnected and open porous Mg-6.3Gd bone scaffolds for compression test analyses.
Martin Wolff +5 more
doaj +1 more source
Ceramics, 2023 Three-dimensionally printed fine-grained refractory ceramics ready for use in contact with liquid steel based on developed one-step thermal debindable ceramic filaments that do not require any chemical solvent pre-debinding are investigated.
Serhii Yaroshevskyi +6 more
doaj +1 more source
Presintered Titanium-Hydroxyapatite Composite Fabricated via PIM Route
Metals, 2021 Ti6Al4V-HA composites have been recognized for their potential for biomedical implantation purposes. In the present study, Ti6Al4V-HA composites were fabricated by Powder Injection Molding (PIM) route.
Nurul Nadiah Mahmud +3 more
doaj +1 more source