Results 11 to 20 of about 450 (154)

Influence of Solvent Type, Specimen Dimensions and Temperature on Chemical Debinding of Alumina Parts Fabricated Via Digital Light Processing [PDF]

Materials Research
Vat photopolymerization via digital light processing (DLP) enables the rapid fabrication of high-resolution ceramic components. However, careful post-processing is required to remove the hardened resin and consolidate the microstructure.
J. P. F. Matheus, A.P. Luz
doaj   +1 more source

Comparison between compression tested and simulated Mg-6.3Gd bone scaffolds produced by binder based additive manufacturing technique

Journal of Magnesium and Alloys, 2023
In this study, a binder based 3D-printing technology viz. Fused Granular Fabrication (FGF) technique was used to produce interconnected and open porous Mg-6.3Gd bone scaffolds for compression test analyses.
Martin Wolff, Mohammad Marvi-Mashhadi, Eshwara Nidadavolu, Henrik Lüneburg, Thomas Ebel, Regine Willumeit-Römer   +5 more
doaj   +1 more source

Presintered Titanium-Hydroxyapatite Composite Fabricated via PIM Route

Metals, 2021
Ti6Al4V-HA composites have been recognized for their potential for biomedical implantation purposes. In the present study, Ti6Al4V-HA composites were fabricated by Powder Injection Molding (PIM) route.
Nurul Nadiah Mahmud, Abu Bakar Sulong, Bhupendra Sharma, Kei Ameyama   +3 more
doaj   +1 more source

Injection Molding of Silicon Nitride with Solvent Debinding.

Journal of the Japan Society of Powder and Powder Metallurgy, 1992
The recent research of Powder Injection Molding (PIM) is begining to be shifted to reducing the debinding time and keeping the shape during debinding. Though there are some methods of removing the binders, the solvent debinding which can solve the problems mentioned above becomes to get much attenion.Here discussed the injection molding of silicon ...
Ono, Katsushi, Kaneko, Yasunari, Kankawa, Yoshimitsu, Saitou, Katsuyoshi, Kasahara, Norio   +4 more
openaire   +2 more sources

Polylactic acid as biobased binder for the production of 3D printing filaments for Ti6Al4V alloy manufacturing via bound metal deposition

Journal of Materials Research and Technology, 2023
In this paper, a biobased binder mainly composed of polylactic acid (PLA) was developed for the production of Ti6Al4V feedstock suitable for 3D printing via material extrusion.
Mario Bragaglia, Matteo Mariani, Claudia Sergi, Fabrizio Sarasini, Jacopo Tirillò, Francesca Nanni   +5 more
doaj   +1 more source

New processing route for ZrSiO4 by powder injection moulding using an eco-friendly binder system

Boletín de la Sociedad Española de Cerámica y Vidrio, 2015
New processing route has been developed for zircon based on powder injection moulding (PIM). Raw zircon powders, obtained from mineral sands, have been processed using a new water soluble binder system composed of PEG and CAB.
Carolina Abajo, Antonia Jiménez-Morales, José Manuel Torralba   +2 more
doaj   +1 more source

Enabling fast debinding of ceramic vat photopolymerization prints with supercritical carbon dioxide as a solvent

Additive Manufacturing, 2023
Peer ...
Nonna Nurmi, Erkka J. Frankberg, Milla Rinne, Teemu Sandblom, Piie Konnunaho, Erkki Levänen   +5 more
openaire   +3 more sources

Fabricating Metal Powder Filters with Material Extrusion Additive Manufacturing [PDF]

Archives of Metallurgy and Materials
Metal powder filters are key components in semiconductor manufacturing equipment that play a critical role in preventing the ingress of impurities and fine particles that may be contained in process gases.
Min-Ji Kim, Min-Jeong Lee, Hyun-Ju Kim, Ju-Yong Kim, Jung-Woo Lee, Jung-Yeul Yun   +5 more
doaj   +1 more source

316L FFF binder development and debinding optimization

Materials Research Express, 2021
Fused Filament Fabrication (FFF) technology is used to create metal parts in this paper. A binder formula is developed for 316L stainless steel powder, composed of polypropylene (PP), styrene ethylene butylene styrene (SEBS) and paraffin wax (PW).
Xinfeng Kan, Dengcui Yang, Zhengzhi Zhao, Jiquan Sun   +3 more
doaj   +1 more source

Extrusion-Based 3D Printing of CuSn10 Bronze Parts: Production and Characterization

Metals, 2021
The interest in producing cost-effective 3D printed metallic materials is increasing day by day. One of these methods, which has gained much attention recently, is the fused deposition modelling (FDM) method.
Ahmet Çağrı Kılınç, Ali Aydın Goktas, Özgür Yasin Keskin, Serhan Köktaş   +3 more
doaj   +1 more source