Results 141 to 150 of about 399 (194)

Tribological and Structural Properties of Copper-Coated 3D-Printed Parts from Biodegradable Polymers. [PDF]

open access: yesMicromachines (Basel)
Feraru Ilie M   +5 more
europepmc   +1 more source
Some of the next articles are maybe not open access.

Related searches:

Detonation Spraying of Metal Carbides Composites

Materials Science Forum, 2021
Detonation spraying is used for the binary fuel spraying, C2H2/C3H8/O2 of WC/Co and Cr3C2/NiCr powder. The particles-in-flight temperature and velocity are calculated and optimized. Spraying distance is varied from 50 to 400 mm and substrate inclination relatively spraying direction is varied up to 60o. Coating properties: microstructure, microhardness,
Ulianitsky, V.   +4 more
openaire   +1 more source

Deposition of Tungsten Coatings by Detonation Spraying

Surface and Coatings Technology, 2021
Abstract Tungsten is a promising material for plasma-facing components of thermonuclear reactors. In the present work, tungsten coatings of low residual porosity (1%) were deposited on copper substrates by detonation spraying. Calculations of the particle temperatures and velocities were conducted for tungsten particles of different sizes using a ...
Igor S Batraev   +2 more
exaly   +2 more sources

Suspension Detonation Spraying of Ceramic Coatings

Combustion, Explosion and Shock Waves, 2019
Experiments on detonation spraying of ceramic coatings are for the first time carried out by feeding a powder as a part of a suspension into a barrel. Spraying of Al2O3, TiO2, and hydroxyapatite nanopowders shows that the new method for obtaining coatings (suspension detonation spraying) can be implemented on a CCDS2000 detonation device.
Alexandr A Shtertser   +2 more
exaly   +3 more sources

Pseudoundercompressed detonation in sprays

Combustion, Explosion, and Shock Waves, 1985
The authors verify that it is necessary to make a more accurate model of the processes occuring in the detonation wave, in particular, fragmentation of drops and mixing, the effect of the walls, change in the heat effect in the reaction zone owing to dissociaiton and recombination processes. The latter are studied in this work.
D. V. Voronin, V. V. Mitrofanov
openaire   +1 more source

Investigations on multicycle spray detonations

Frontiers of Energy and Power Engineering in China, 2007
Experimental investigations were carried out on a 50-I.D. multicycle pulse detonation engine (PDE) model, and liquid fuel (gasoline) was used. The average of pressure peak, as measured by piezoelectricity pressure transducer, increased versus distance to thrust wall before fully-developed detonation came into being.
Mu Li   +4 more
openaire   +1 more source

Calculation of detonation gas spraying

Combustion, Explosion, and Shock Waves, 2007
A model of processes in the barrel of a detonation facility for application of powder coatings, which takes into account the variable composition of the working gases in the barrel, is presented. It is demonstrated that varying the volume of the gas mixer is an effective tool for stabilizing particle parameters and coating properties if powders with ...
T. P. Gavrilenko, Yu. A. Nikolaev
openaire   +1 more source

Characterization of Detonation Sprayed Coatings

International Thermal Spray Conference, 2011
Abstract Characterization of coatings made with the help of Computer Controlled Detonation Spraying (CCDS) was performed. The applied coatings include hard alloys (WC/Co -75/25, WC/Co - 88/12, WC/Co/Cr - 86/10/4, and Cr2C3 / NiCr), aluminum oxide, nickel-chromium self-fluxing alloy, titanium, bronze, and stainless steel.
A. A. Shtertser   +3 more
openaire   +1 more source

A model for spray detonations

Acta Astronautica, 1979
Abstract In some cases of spray detonations, blast waves originating from the droplets have been observed. These blast waves eventually catch up with the main front thus providing a means of energy transfer to the front and therefore maintaining a steadily propagating wave.
openaire   +1 more source

Home - About - Disclaimer - Privacy