Results 181 to 190 of about 59,667 (255)

Differential Semiology in Video-EEG Monitoring: A Clinical Approach to Distinguishing Psychogenic Nonepileptic and Epileptic Seizures. [PDF]

Cureus
Pejanovic-Skobic N, Krtalic N, Bender M, Pravdic N, Batinic D.   +4 more
europepmc   +1 more source

Multilayer Self‐Limiting Electrospray Deposition via Stepped Voltage Bias

Advanced Engineering Materials, EarlyView.
Self‐limiting electrospray deposition (SLED) uses a high voltage to generate and deposit a charged payload on a target surface. The coating retains its charge, repelling newly arriving material. SLED thickness can be decreased by applying a secondary bias to the target.
Madhuri Deb, S. Rahman Pejman, Alexander Jakimowicz, Jonathan P. Singer   +3 more
wiley   +1 more source

Energy efficient approximate compressor architectures for high performance image multiplication in CNTFET technology. [PDF]

Sci Rep
Foroutan P, Navi K.
europepmc   +1 more source

Uniform Amorphization of Crystalline Silicon Surfaces Enabled by Deep Ultraviolet Femtosecond Laser Pulses

Advanced Engineering Materials, EarlyView.
Deep‐UV (258 nm) femtosecond pulses enable uniform amorphous silicon writing on Si(100)/(111) with a six‐fold larger fluence amorphization window than NIR methods. Optimized fluence and overlap yield 20–45 nm uniform and continuous amorphous layers. Microscopy shows sharp interfaces, and real‐time reflectivity reveals nanosecond melt–resolidification ...
Wissal Benali, Magali Gregoire, Matys Guyard, Tatiana Itina, David Grojo, Pol Sopeña   +5 more
wiley   +1 more source

Reservoir Dynamics in Vibrational Polaritons Revealed by Detuning-Dependent Ultrafast Spectroscopy. [PDF]

J Phys Chem Lett
Gutierrez A, Stemo G, Nishiuchi J, Kiyokawa M, Katsuki H.   +4 more
europepmc   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Linear Multiplication Beyond Geiger Mode Threshold in Ge-on-Si Avalanche Photodiode. [PDF]

Micromachines (Basel)
Zhao D, Wen Q, Liu F, Qi W, Du S.
europepmc   +1 more source

Model‐Guided Design of Paper Membrane Architectures for Controlled Flow and Enhanced Diagnostic Sensitivity

Advanced Engineering Materials, EarlyView.
Geometrical modifications on nitrocellulose membranes can result in observable differences in signal intensity relative to a reference membrane (top and bottom left). Using two reference experiments, we have developed a theoretical model that can reproduce the experimentally observed flow changes and provide information on membrane parameters, e.g ...
Maria Dimaki, Lea Holritz, Winnie E. Svendsen   +2 more
wiley   +1 more source

An FPGA-Based Event-Timing Front-End for Time-Resolved Sensing with Dual-Mode Experimental Characterization. [PDF]

Sensors (Basel)
Núñez J, Fiorelli R.
europepmc   +1 more source

Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials

Advanced Engineering Materials, EarlyView.
Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley   +1 more source