Results 1 to 10 of about 837,527 (297)
Mathematical Modeling of Heating and Strain Aging of Steel during High-Speed Wire Drawing
Metals, 2022 In this article, a mathematical model of the wire’s average temperature change in the process of multiple drawing on high-speed straight-line drawing machines has been developed.
Liudmila V. Radionova +8 more
doaj +3 more sources
Journal of Magnesium and Alloys, 2022 Compared to cold drawing, dieless drawing has shown great potential for manufacturing biodegradable Mg alloy microtubes due to the large reduction in area acquired in a single pass.
Peihua Du +2 more
doaj +3 more sources
FINITE ELEMENT ANALYSIS STUDY ON DEEP DRAWING SPEED PUNCH
Nonconventional Technologies Review, 2015 Analysis drawing process can sometimes be quite expensive and time consuming. Finite Element analysis manages to solve some of these shortcomings. It is very important that the results obtained by finite element simulation to be close to those obtained ...
Alin Pop, Ioan Radu, Florin Blaga
doaj +1 more source
The Effect of Drawing Speed on the Ageing of High-Carbon Steel Wire [PDF]
Archives of Metallurgy and Materials, 2018 The paper analyzes the effect of ageing on the variations in the mechanical and technological properties of steel wire. The process of drawing 5.5 mm-diameter wire rod into 1.70 mm wire was carried out in 12 draws on a Koch KGT multi-stage drawing ...
M. Suliga
doaj +1 more source
Research of zinc coatings in thin medium carbon steel wires [PDF]
Archives of Metallurgy and Materials, 2019 An analysis of the effect of drawing speed on the formation of a zinc coating in the multi-stage fine steel wire drawing process has been carried out in the article. Pre-hardened 2.2 mm-diameter material was drawn into 1.00 mm-diameter wire in 6 draws on
M. Suliga, R. Wartacz, H. Kania
doaj +1 more source
Effect of the Drawing Speed on the Delaminations in the Torsion Test of High-Carbon Steel Wires [PDF]
Archives of Metallurgy and Materials, 2019 In this paper, an attempt was made to explain the causes of surface delamination in high carbon steel wires during the torsion test. For end wires with 1.7 mm diameter drawn at speeds of 5, 10, 15, 20, 25 m/s, technological tests were carried out.
M. Suliga
doaj +1 more source
Unique Path Method of the Pinch-Out Profile Based on Unified Stratigraphic Sequence
Geosciences, 2021 Pinch-outs refers to the gradual thinning of the thickness of the sedimentary layer laterally until there is no deposition and are a major topic of modern research on the automated drawing of geological profiles. The rapid development of smart geological
Zhen Liu +4 more
doaj +1 more source
Analysis of Fiber Drawing in Wet Spinning for Surface Roughness [PDF]
MATEC Web of Conferences, 2021 The drawing process behavior was investigated with focus on fiber stretching speed (spinning acceleration) to improve luster quality of fibers. Wet spinning method has a limitation of low luster at high spinning speed.
Fukui Yuta +2 more
doaj +1 more source
Journal of Manufacturing and Materials Processing, 2023 Warm forming is widely used to enhance the formability of aluminum alloy sheets. In warm deep drawing, the process variables significantly affect frictional characteristics at the tool–blank interface.
Archit Shrivastava, Ravi Kumar Digavalli
doaj +1 more source
The Influence of Organizational Speed on Organizational Mishaps: The Moderating Role of Dynamism [PDF]
, 2016 Previous studies have shown the importance of organizational speed for firms’ competitive advantage and financial performance. However, more recent studies have also demonstrated that speed can be detrimental for companies.
Martin-Tapia, Inmaculada +2 more
core +1 more source