Results 251 to 260 of about 353,538 (308)

Life cycle and techno-economic assessment of a solar-biogas hybrid dryer for banana drying. [PDF]

PLoS One
Shigella O, Loemba ABT, Yawe J, Kichonge B, Mwema MF.   +4 more
europepmc   +1 more source

Study on the degradation mechanism and performance improvement of coal gangue-based shotcrete under high-salt dry-wet cycling conditions in underground mining environments. [PDF]

Sci Prog
Wu H, Gao M, Chen S, Ren H, Hu Z, Li M, Guo C, Guo Z.   +7 more
europepmc   +1 more source

Dimensional Stability of Beech Wood: The Influence of Taper, Slope of Annual Ring and Sawing Pattern. [PDF]

Polymers (Basel)
Vilkovský P, Vilkovská T, Klement I, Fúčela M.   +3 more
europepmc   +1 more source

Optimization of fluidized bed drying process parameters and quality evaluation of ready to use onion slices. [PDF]

Sci Rep
Faisal S, Yousuf A, Langoo BA, Mishra S, Muzamil M, Ali M, Richa R, Kumar V, Khan JM, Saris PEJ, Gupta AK, Naik B.   +11 more
europepmc   +1 more source

Dryeration: Better Corn Quality with High Speed Drying

, 1900
McKenzie, B. A., Foster, G. H., Noyes, R. T., Thompson, R. A.   +3 more
openaire   +1 more source

Some of the next articles are maybe not open access.

Related searches:

High-speed dry electrical discharge machining

International Journal of Machine Tools and Manufacture, 2015
Abstract A novel high-speed dry electrical discharge machining (EDM) method was proposed in this study. Using this method, the material can be rapidly melted by extremely high discharge energy and flushed out of the discharge gap by high-pressure and high-speed air flow.
Yang Shen, Yonghong Liu, Yanzhen Zhang, Hang Dong, Wanyun Sun, Xiaolong Wang, Chao Zheng, Renjie Ji   +7 more
openaire   +1 more source

High-speed dry compound machining of Ti6Al4V

Journal of Materials Processing Technology, 2015
Abstract Milling experiments on Ti6Al4V using high-speed compound machining with high-speed air dielectric were conducted in this study. The new and efficient compound machining combines arc machining and electrical discharge machining (EDM) together, both of them are working in parallel. Ti6Al4V can be quickly melted by significantly high processing
Yang Shen, Yonghong Liu, Wanyun Sun, Hang Dong, Yanzhen Zhang, Xiaolong Wang, Chao Zheng, Renjie Ji   +7 more
openaire   +1 more source

High Speed 3D Milling by Dry EDM

CIRP Annals, 2003
Abstract This paper describes the high speed EDM milling of 3D cavities using gas as the working fluid. In this new process, the molten workpiece material is removed and flushed out of the working gap with the help of high-pressure gas flow. The advantages or this technique are the remarkably small tool electrode wear and the significantly high ...
Masanori Kunleda, Yukinori Miyoshi, Tsutomu Takaya, Nobuhiro Nakajima, Yu ZhanBo, Masahiro Yoshida   +5 more
openaire   +1 more source

High-speed near dry electrical discharge machining

Journal of Materials Processing Technology, 2016
Abstract High-speed near dry electrical discharge machining (EDM) is a novel and promising machining method, which obtains higher material removal rate, lower surface roughness and thinner width of overcut compared with that of high-speed dry EDM.
Yang Shen, Yonghong Liu, Wanyun Sun, Yanzhen Zhang, Hang Dong, Chao Zheng, Renjie Ji   +6 more
openaire   +1 more source

Speed control for automated manual transmission with dry clutch

2004 43rd IEEE Conference on Decision and Control (CDC) (IEEE Cat. No.04CH37601), 2004
Automated manual transmissions (AMTs) with dry clutches are becoming more and more used as an improving add-on solution on classical manual transmission systems and as a reconfiguration element in modern hybrid electric vehicles. Due to the two possible states of the clutch (engaged or not) and to the different gear ratios AMTs can be considered as a ...
Glielmo L, Iannelli L, Vacca V, Vasca F
openaire   +1 more source