Results 91 to 100 of about 149,709 (288)
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Probing nanoscale oxygen ion motion in memristive systems
Nature Communications, 2017 Ion transport in solid-state materials is a fundamental process for many modern technologies. Utilizing electrostatic force microscopy, Yanget al. directly visualize ion motion and verify the oxygen ion dynamics within HfO2—a common metal-oxide based ...
Yuchao Yang +5 more
doaj +1 more source
Ohmic-to-Schottky Modification of Zno-Metal Contact Modulated by Film Thickness [PDF]
Materials ResearchThis work investigated the charge transport behavior at the interface between a Pt-Ir metal contact and transparent zinc oxide (ZnO) electrodes with one, four, and eight ZnO layers.
Raquele Lima Moreira +4 more
doaj +1 more source
Detection mechanism for ferroelectric domain boundaries with lateral force microscopy
, 2006 The contrast mechanism for the visualization of ferroelectric domain boundaries with lateral force microscopy is generally assumed to be caused by mechanical deformation of the sample due to the converse piezoelectric effect.
Elisabeth Soergel +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source
Thermophysical Properties of the Desulphurization Slags With Various CaS and CaO/Al2O3 Ratio
Advanced Engineering Materials, EarlyView.This article investigates how CaS content and the CaO/Al2O3 ratio influence the thermophysical properties of desulphurization slags. Using experimental measurements and thermodynamic simulations, this study reveals complex effects on viscosity, surface tension, and density, providing new insight into slag structure and phase behavior under ...
Eldar Salpagarov +4 more
wiley +1 more source
Interactions between Silica Particles in the Presence of Multivalent Coions
, 2017 Forces between charged silica particles in solutions of multivalent coions are measured with colloidal probe technique based on atomic force microscopy.
Trefalt, Gregor +2 more
core +2 more sources
Advanced Engineering Materials, EarlyView.Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi +7 more
wiley +1 more source
Kelvin probe force microscopy in liquid using electrochemical force microscopy
Beilstein Journal of Nanotechnology, 2015 Conventional closed loop-Kelvin probe force microscopy (KPFM) has emerged as a powerful technique for probing electric and transport phenomena at the solid–gas interface.
Liam Collins +6 more
doaj +1 more source
Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena +2 more
wiley +1 more source