Results 151 to 160 of about 691,599 (315)

Molecular Dynamics Studies of Shape Memory Polymers: From Bead–Spring Models to Atomistic Simulations

Advanced Engineering Materials, EarlyView.
Coarse‐grained (left) and atomistic (right) models of the shape memory polymer ESTANE ETE 75DT3 are shown schematically. The two representations bridge molecular detail and mesoscopic description. Both models capture shape memory behavior, linking segmental mobility and conformational relaxation of anisotropic chains to macroscopic recovery, and ...
Fathollah Varnik
wiley   +1 more source

Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello, Joachim Gussone, Suzana G. Fries, Marcus Rackel, Andreas Stark, Norbert Schell, Jan Haubrich, Guillermo Requena   +7 more
wiley   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Advanced Electron Microscopy and Microcomputed Tomography Analysis of Single‐Crystal Ni‐Base Superalloys After Short‐Term Multiaxial Creep

Advanced Engineering Materials, EarlyView.
This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome, Lijie Cao, Christoph Somsen, Johannes Boes, René Hesse, Werner Theisen, Gunther Eggeler   +6 more
wiley   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

External and Internal Cracking Caused by Heat Treatment in Laser Powder Bed Fusion‐Fabricated Inconel 738LC Components

Advanced Engineering Materials, EarlyView.
Manufacturing problems such as heat treatment‐induced cracking hinder the widespread application of the laser powder bed fusion (LPBF) process to superalloys. In this study, cracks in the LPBF components of Inconel 738LC superalloy are characterized after heat treatment at various temperature ranges, revealing two distinct cracking behaviors.
Kosuke Kuwabara, Masahiro Kusano, Ayako Ikeda, Toshio Osada, Makoto Watanabe   +4 more
wiley   +1 more source

Additive Manufacturing of Alumina‐Reinforced Elastomers

Advanced Engineering Materials, EarlyView.
Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani, Zongwen Fu, Robert Göstl, Hamed Shokri, Carmine Putignano, Gianluca Percoco, Bilal Gökce   +6 more
wiley   +1 more source

Prediction of axial elongation in adults with high myopia: the Wenzhou High Myopia Cohort Study. [PDF]

Eye Vis (Lond)
Wang Y, Rui X, Sun Y, Li Y, Ding S, Zhang Z, Lu J, Wu M, Qu J, Zhou X, Wu H.   +10 more
europepmc   +1 more source