3D‐Printed Architected Material for the Generation of Foam‐Based Protective Equipment
Advanced Engineering Materials, EarlyView.This study investigates 3D‐printed architected structures as alternatives to traditional foams in protective gear. It focuses on customizing impact strength and damping through design and manufacturing integration. Testing shows these structures outperform conventional foams, offering enhanced customizability, lower weight, and tunable performance ...
Ali Zolfagharian +5 more
wiley +1 more source
Clinical and magnetic resonance imaging characteristics of thoracolumbar intervertenral disk extrusions and protrusions in large breed dogs [PDF]
, 2002 It has recently been shown that the fat-derived hormone adiponectin has the ability to decrease hyperglycemia and to reverse insulin resistance. However, bacterially produced full-length adiponectin is functionally inactive. Here, we show that endogenous
Beltran, E +5 more
core +4 more sources
Fault detection and diagnosis of a plastic film extrusion process [PDF]
, 2010 This paper presents a new approach to the design of a model-based fault detection and diagnosis system for application to a plastic film extrusion process. The design constructs a residual generator via parity relations.
DuPont Teijin Films UK Ltd (Funder) +4 more
core +1 more source
Effect of frictional boundary conditions and percentage area reduction on the extrusion pressure of Aluminum AA6063 alloy using FE analysis modelling [PDF]
, 2020 © 2020 by the authors; licensee Growing Science, Canada. This is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC-BY) license (http://creativecommons.org/licenses/by/4.0/).Finite Element Analysis ...
Ismail, Sikiru O. +2 more
core +2 more sources
Advanced Engineering Materials, EarlyView.The share of technical thermoplastics is expected to grow further in the e‐mobility segment. In this study, a detailed temperature‐based tribological characterization of technical thermoplastics is performed. The tribological properties are discussed in terms of the dynamic mechanical properties of polymers at different ambient temperatures. A proof of
Harsha Raghuram +2 more
wiley +1 more source
Hydrodynamic modelling of hydrostatic magnesium extrusion [PDF]
, 2006 Wilson’s hydrodynamic model of the hydrostatic extrusion process is extended to meet the geometry found on residual billets. The transition from inlet\ud to work zone of the process is not considered sharp as in the model of Wilson but as a rounded edge,
Moodij, E. +2 more
core +2 more sources
The effect of pressure and temperature variations on the FEM prediction of deformation during extrusion [PDF]
, 2005 The extrusion process is complex, involving interaction between the process variables and the material’s high temperature properties and is typically conducted at relatively high temperatures because the lower flow stress of the material permits larger ...
Flitta, Isaac, Sheppard, Terry
core +1 more source
Subgrain and Cavity Development during Creep of Al‐3.85%Mg
Advanced Engineering Materials, EarlyView.Al‐3.85%Mg does form subgrains if crept at very high strains. This fact allows the unification of the creep description in two different alloys such as pure Al and Al–Mg alloys. It is classically considered that the creep mechanisms for type M (e.g., pure Al) and type A alloys (e.g., Al–Mg alloys) are different.
Augusta Isaac +6 more
wiley +1 more source
Modelling the Effect of Process Parameters on the Wet Extrusion and Spheronisation of High-Loaded Nicotinamide Pellets Using a Quality by Design Approach [PDF]
, 2019 Open access articleThe aim of the present study was to develop an alternative process to spray granulation in order to prepare high loaded spherical nicotinamide (NAM) pellets by wet extrusion and spheronisation.
Keppler, Julia K +4 more
core +2 more sources
Development of Aluminum Scandium Alloys for Hydrogen Storage Valves
Advanced Engineering Materials, EarlyView.Different aluminum alloy series and various aluminum‐scandium alloys with differing Sc and Zr levels are evaluated for use in hydrogen storage valve production. The alloys undergo hardness testing, optical microscopy, and tensile strength analysis, with hardening behavior studied under varying conditions.
Francisco García‐Moreno +4 more
wiley +1 more source