Results 101 to 110 of about 127,598 (206)

Projekt for manufacturing of gears for Company Stab spol. s r. o. [PDF]

, 2020
Diplomová práca opisuje projekt na založenie novej divízie pre firmu ktorá sa zaoberá generálnymi opravami strojov. V prvej časti práce je rozoberaná teoretická časť o výrobnom procese ozubenia a ekonomická časť tejto práce. Hlávne časti práce sú analýza
Štefan Staník
core  

Surface quality improvement of AZ31 Mg alloy by a combination of modified Taguchi method and simple multi objective optimization procedure

Cogent Engineering
The motive of this study is to evaluate the machinability properties of AZ31 Mg alloy in the face milling operations. Depth of cut, rate of feed and speed of cut are three input variables in the face milling process, while surface roughness (Ra) and tool
Muni Tanuja Anantha, Sireesha Koneru, Parameshwaran Pillai Thiruvambalam Pillai, Nageswara Rao Boggarapu, Tanya Buddi, Kseniia Iurevna Usanova, Rajesh Deorari   +6 more
doaj   +1 more source

Investigation of tool geometry effect and penetration strategies on cutting forces during thread milling [PDF]

, 2014
The application of thread milling is increasing in industry because of its inherent advantages over other thread cutting techniques. The objective of this study is to investigate the effect of milling cutter tool geometry on cutting forces during thread ...
BRENDLEN, Romain, FROMENTIN, Guillaume, POULACHON, Gérard, SHARMA, Vishal   +3 more
core   +3 more sources

Monitoring face-mill geometry [PDF]

Russian Engineering Research, 2013
N. V. Kolesov, N. N. Petrosyan
openaire   +1 more source

Modeling dynamics and stability of 5-axis milling processes [PDF]

, 2007
5-axis milling is an important machining process for several industries such as aero-space, automotive and die/mold. It is mainly used in machining of sculptured surfaces where surface quality is of extreme importance.
Budak, Erhan, Ozlu, Emre, Ozturk, Erdem, Özlü, Emre, Öztürk, Erdem   +4 more
core  

Фрезерная головка [PDF]

, 1995
У публікації розглянуто конструкцію агрегатної фрезерної головки з індивідуальним приводом. Головка містить опорну плиту і підшипники кочення. Торцева фреза встановлена в осьовому напрямку на трьох (як мінімум) підшипниках.
Kushnirov, Pavlo Vasylovych, Toporov, Oleg Oleksiyovich, Кушниров, Павел Васильевич, Кушніров, Павло Васильович, Топоров, Олег Алексеевич, Топоров, Олег Олексійович   +5 more
core  

用于大尺寸圆形辊车铣加工的特种车床传动系统的设计

Jixie chuandong, 2012
The research and design of a new transmission system for special purpose lathe for turn-milling of large dimension rollers are introduced.Based on face lathe,a new transmission system is built by adding transmission components and milling components,thus
孙培明, 龚善初
doaj  

Studied validation of finite element modeling for titanium alloy (Ti-6Al-4V) at face milling. [PDF]

Heliyon, 2023
Ali MH.
europepmc   +1 more source

Tool Life of PM-HSS Cutting Tools when Milling of Titanium Alloy [PDF]

, 2017
Machining of titanium alloys meets with poor life of a cutting tool. It is caused by a low thermal conductivity and by a high strength-to-weight ratio of the alloys. Various approaches for cost-effective and productive machining titanium alloys are still
Bach P., Trmal G., Zeman P.
core  

Percentage Ratios of Cutting Forces during High-Reed Face Milling. [PDF]

Materials (Basel), 2022
Reznicek M, Horava C, Ovsik M.
europepmc   +1 more source