Results 81 to 90 of about 201,563 (265)

Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids

Advanced Functional Materials, EarlyView.
This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow, Samya Sen, Joaquin Yus, Eliza E. Lovrich, Amanda G. Hoika, Kelly M. Chang, Arielle A. Pfeil, Nellie Haug, Amy J. Wagoner Johnson, Randy H. Ewoldt   +9 more
wiley   +1 more source

Selection of lansoprazole from an FDA-approved drug library to inhibit the Alzheimer’s disease seed-dependent formation of tau aggregates

Frontiers in Aging Neuroscience
The efficacy of current treatments is still insufficient for Alzheimer’s disease (AD), the most common cause of Dementia. Out of the two pathological hallmarks of AD amyloid-β plaques and neurofibrillary tangles, comprising of tau protein, tau pathology ...
Ahmed Imtiaz, Ahmed Imtiaz, Shotaro Shimonaka, Mohammad Nasir Uddin, Montasir Elahi, Koichi Ishiguro, Masato Hasegawa, Nobutaka Hattori, Yumiko Motoi   +8 more
doaj   +1 more source

NSs Filament Formation Is Important but Not Sufficient for RVFV Virulence In Vivo

Viruses, 2019
Rift Valley fever virus (RVFV) is a mosquito-borne phlebovirus that represents as a serious health threat to both domestic animals and humans. The viral protein NSs is the key virulence factor of RVFV, and has been proposed that NSs nuclear filament ...
Shufen Li, Xiangtao Zhu, Zhenqiong Guan, Wenfeng Huang, Yulan Zhang, Jeroen Kortekaas, Pierre-Yves Lozach, Ke Peng   +7 more
doaj   +1 more source

Sebaceous Filaments

Dermatology Practical & Conceptual, 2021
Yuvraj Singh, Shekhar Neema, Amit Bahuguna, Disha Dabbas   +3 more
openaire   +4 more sources

All‐in‐One Analog AI Hardware: On‐Chip Training and Inference with Conductive‐Metal‐Oxide/HfOx ReRAM Devices

Advanced Functional Materials, EarlyView.
An all‐in‐one analog AI accelerator is presented, enabling on‐chip training, weight retention, and long‐term inference acceleration. It leverages a BEOL‐integrated CMO/HfOx ReRAM array with low‐voltage operation (<1.5 V), multi‐bit capability over 32 states, low programming noise (10 nS), and near‐ideal weight transfer.
Donato Francesco Falcone, Victoria Clerico, Wooseok Choi, Tommaso Stecconi, Folkert Horst, Laura Bégon‐Lours, Matteo Galetta, Antonio La Porta, Nikhil Garg, Fabien Alibart, Bert Jan Offrein, Valeria Bragaglia   +11 more
wiley   +1 more source

Intermediate Resistive State in Wafer‐Scale Vertical MoS2 Memristors Through Lateral Silver Filament Growth for Artificial Synapse Applications

Advanced Functional Materials, EarlyView.
In MOCVD MoS2 memristors, a current compliance‐regulated Ag filament mechanism is revealed. The filament ruptures spontaneously during volatile switching, while subsequent growth proceeds vertically through the MoS2 layers and then laterally along the van der Waals gaps during nonvolatile switching.
Yuan Fa, Milan Buttberg, Ke Ran, Rana Walied Ahmad, Dennis Braun, Lukas Völkel, Jimin Lee, Sofía Cruces, Bart Macco, Bárbara Canto, Holger Lerch, Thorsten Wahlbrink, Holger Kalisch, Michael Heuken, Andrei Vescan, Joachim Mayer, Zhenxing Wang, Ilia Valov, Stephan Menzel, Max C. Lemme   +19 more
wiley   +1 more source

Integration of Low‐Voltage Nanoscale MoS2 Memristors on CMOS Microchips

Advanced Functional Materials, EarlyView.
This article presents the first monolithic integration of nanoscale MoS2‐based memristors into the back‐end‐of‐line of foundry‐fabricated CMOS microchips in a one‐transistor‐one‐resistor (1T1R) architecture. The MoS2‐based 1T1R cells exhibit forming‐free, nonvolatile resistive switching with ultra‐low operating voltages, low cycle‐to‐cycle variability ...
Jimin Lee, Sofía Cruces, Xiaohua Liu, Yang Chen, Vasilis A. Maroufidis, Janghyun Jo, Lukas Völkel, Dennis Braun, Michael Möller, Leon Brackmann, Holger Kalisch, Michael Heuken, Andrei Vescan, Rafal E. Dunin‐Borkowski, Joachim Mayer, Stefan Wiefels, Max C. Lemme   +16 more
wiley   +1 more source

ANALYSIS OF THE CUTTING BLADE FOR HDPE AND PET PLASTIC BOTTLE SHREDDERS FOR 3D PRINTING FILAMENT EXTRUSION

Rekayasa Mesin
The increasing use of filaments for 3D printing encourages the use of suitable plastic waste as a raw material for filaments. In Indonesia, plastic waste will reach 26.2 million tons in 2023, with 18.47% of it being plastic. To process plastic waste such
Riky Adhiharto, Cahya Ramdan Putra Mandayusdi, Meri Rahmi   +2 more
doaj   +1 more source

Strain‐Programmable Luminescent Adhesive Patch With Tartrazine‐Mediated Optical Skin Clearing for Photochemical Tissue Bonding

Advanced Functional Materials, EarlyView.
We propose a suture‐complementary approach that integrates optical skin clearing with a strain‐programmable luminescent adhesive patch. Hyaluronic acid promotes transdermal delivery of tartrazine to improve optical clearing and stabilizes its interaction with a photosensitizer. Optical clearing increases the penetration depth of visible light into skin,
Seong‐Jong Kim, Kyungjoo Jo, Kwanghyeon Park, Jun Hee Kim, Jong Hyeong Cho, Inhoo Choi, Sei Kwang Hahn   +6 more
wiley   +1 more source

Equipment and technology for ensuring the strength characteristics of polymer products in 3D printing with composite filament

Известия высших учебных заведений. Поволжский регион:Технические науки
Backround. Polymer products produced by 3D printing are inferior in strength characteristics to cast parts. To increase the strength characteristics, impact strength and heat resistance of products, a composite filament was created, and a technology ...
A.E. Zverovshchikov, I.V. Bantysh, V.Z. Zverovshchikov   +2 more
doaj   +1 more source