Results 131 to 140 of about 171,915 (303)
Materials Research ExpressThe anisotropy in mechanical properties of additively manufactured (AM) superalloys, closely related to grain morphology, grain boundaries, and precipitated phases, impedes their aerospace applications.
Lei Shi +4 more
doaj +1 more source
Initiation of internal fatigue crack in a carbide-free bainitic steel during high cycle fatigue
Journal of Materials Research and TechnologyThe crack initiation stage is crucial to the overall fatigue behavior of the carbide-free bainitic steels. Through S–N curve testing and fracture observation, it is demonstrated that internal crack initiation is the dominant mode during high cycle ...
Bo Mi +5 more
doaj +1 more source
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source
Growth response to temperature of two maize (Zea mays L.) hybrids with differing levels of cold tolerance : a thesis presented in partial fulfillment of the requirements for the degree of Master of Agricultural Science in Plant Science (Seed Technology), Massey University [PDF]
, 1993 Low temperatures are a hazard to maize production especially in high altitude and high latitude areas (Eagles, 1979; Hardacre and Eagles, 1986) where it may cause substantial yield reductions through its accumulated effect on vegetative and reprodutive ...
Mukumbuta, Mwangala Stephen
core
Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena +2 more
wiley +1 more source
Laboratory study on the effects of hydraulic and granulometric parameters on the response of granular soil to internal erosion [PDF]
, 2019 Erosion is a major environmental problem to agricultural land as well as to civil engineering infrastructures. Rainwater infiltration into granular soils can lead to the migration of fine particles by suffusion.
BENDANI, Karim +2 more
core
The Iowa Grain Quality Initiative
Proceedings of the Integrated Crop Management Conference, 1999 Darren Jarboe, Charles Hurburgh
openaire +2 more sources
THE INITIAL CREEP OF COLUMNAR-GRAINED ICE: PART II. ANALYSIS
Canadian Journal of Physics, 1965 Observations on the initial creep behavior of columnar-grained ice are analyzed by assuming that the creep strain at a given time has a power-law dependence on the applied constant compressive stress. The exponent for the stress was time-dependent during transient creep.
openaire +3 more sources
Advanced Engineering Materials, EarlyView.The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source