Results 131 to 140 of about 100,287 (312)

Slip Localization Intensification Mediated by Grain Boundary Sliding in a Polycrystalline Nickel‐Based Superalloy

Advanced Engineering Materials, EarlyView.
The temperature dependence of fatigue behavior in nickel‐based superalloys is investigated through high‐resolution measurements of plastic localization. While increasing temperature reduces localization and enhances fatigue performance in René 88DT, Inconel 718 exhibits a sharp degradation at intermediate temperature due to intensified slip ...
M. Calvat, D. Anjaria, I. Woo, C. Bean, D. Texier, J. C. Stinville   +5 more
wiley   +1 more source

Speedup vs. Simulation Granularity

, 1996
This paper describes a packet network simulator whose timing granularity can shift continuously from fine, packetlevel detail to coarse, conversation-level detail.
Peter B. Danzig, Jong-Suk Ahn
core  

A Lightweight Procedural Layer for Hybrid Experimental–Computational Workflows in Materials Science

Advanced Engineering Materials, EarlyView.
We unveil a prototype hybrid‐workflow framework that fuses automatedcomputation with hands‐on experiments. Built atop pyiron, a lightweight, parameterized layer translates procedure descriptions into executable manual steps, syncing instrument settings, human interventions, and data capture in real‐time today.
Steffen Brinckmann, Sarath Menon, Raphael Röske, Johannes Steinhülb, Michael Selzer, Jan Janssen, Tilmann Hickel, Ruth Schwaiger, Jörg Neugebauer   +8 more
wiley   +1 more source

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

High‐Temperature Nanoindentation of Metals: Assessing Thermal Drift, Frame Compliance, and Chemical Composition Effects on the Reported Mechanical Properties

Advanced Engineering Materials, EarlyView.
Do not let thermal drift and instrument artifacts deceive high‐temperature nanoindentation results. We compare classical Oliver–Pharr and automatic image recognition analyses across steels and a Ni alloy to quantify these effects. Accounting for artifacts reveals systematic softening with temperature, while Cr and Ni additions boost resistance ...
Velislava Yonkova, Steffen Brinckmann, Ruth Schwaiger   +2 more
wiley   +1 more source

Analysis of Granularity Adjustment for Regulatory Capital

, 2019
The lack of portfolio granularity in terms of exposure has been shown to have important implications for the amount of a financial institution’s economic capital.
Krali, Mario, Gurov, Andrey
core   +1 more source

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Model granularity and related concepts [PDF]

, 2016
Models are integral to engineering design and basis for many decisions. Therefore, it is necessary to comprehend how a model’s properties might influence its behaviour.
Eckert, C. M., Clarkson, P. J., Maier, J. F.   +2 more
core  

Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment

Advanced Engineering Materials, EarlyView.
This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li, Rong Zhao, Qian Zhang, Haojie Wang, Yujing Liu, Lai‐Chang Zhang   +5 more
wiley   +1 more source