Results 191 to 200 of about 1,812,103 (301)

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

Advanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai, Xinrui Sarah Niu, Zhao Qin   +2 more
wiley   +1 more source

Apolipoprotein E is a marker of all chondrocytes in the growth plate resting zone. [PDF]

Bone Res
Kodama J, Oichi T, Wilkinson KJ, Abzug JM, Kaito T, Enomoto-Iwamoto M, Iwamoto M, Otsuru S.   +7 more
europepmc   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Atypical Triplane Ankle Fracture - Antero-Medial Epiphyseal Separation and the Unfused Growth Plate: A Case Report. [PDF]

J Orthop Case Rep
Toner E, White D, Kealey D.
europepmc   +1 more source

Synthesis of a Novel Thermoresponsive S53P4 Bioactive Glass Extract–Poloxamer 407 Injectable Hydrogels: Assessment of Biocompatibility and Antimicrobial Properties

Advanced Engineering Materials, EarlyView.
This study investigates innovative thermoreversible hydrogels derived from S53P4 bioactive glass extracts to aid in the healing of infected diabetic foot wounds. These injectable gels, which gel at body temperature, release beneficial ions and remain stable over time.
Marian G. Vargas Guerrero, Adrian Stiller, Alex Nygård, Matej Krivulka, Lars Galema, Erwin Peters, Jimmy Lucchesi, Peter Uppstu, Leena Hupa, Jacobus J. C. Arts   +9 more
wiley   +1 more source

Longitudinal In Vivo 3T MRI of Naturally Occurring Early Osteochondrosis Lesions in the Piglet Humeral Epiphyseal Cartilage and Growth Plate. [PDF]

J Orthop Res
Armstrong AR, Buko EO, Johnson CP, Tóth F.   +3 more
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Runx2 controls the osteogenic fate of growth plate chondrocytes. [PDF]

Genes Dis
Zeng D, Yu J, Lu K, Yi D, Xia Z, Qin L, Xiao G, Yang X, Tong L, Chen D.   +9 more
europepmc   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source