Results 141 to 150 of about 1,128,145 (247)
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora +4 more
wiley +1 more source
Improved understanding of the loss-of-symmetry phenomenon in the conventional Kalman filter [PDF]
This paper corrects an unclear treatment of the conventional Kalman filter implementation as presented by M. H. Verhaegen and P. van Dooren in Numerical aspects of different Kalman filter implementations, IEEE Trans. Automat. Contr., v. AC-31, no. 10, pp.
Verhaegen, M. H.
core +1 more source
Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres
Advanced Engineering Materials, EarlyView.This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann +3 more
wiley +1 more source
Journal for the History of Analytical PhilosophyAt the end of Frank Ramsey’s “General Propositions and Causality” ([1929b] 1990), he offers an enigmatic footnote that briefly describes his philosophy of science as a “forecasting theory”. What he means by this and by a “forecast” is unclear.
Bruce Rushing
doaj
Additive Gaussian Process Regression for Predictive Design of High‐Performance, Printable Silicones
Advanced Engineering Materials, EarlyView.A chemistry‐aware design framework for tuning printable polydimethylsiloxane (PDMS) for vat photopolymerization (VPP) is developed using additive Gaussian process (GP) modeling. Polymer network mechanics informs variable groupings, feasible formulation constraints, and interaction variables.
Roxana Carbonell +3 more
wiley +1 more source
Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere
Advanced Engineering Materials, EarlyView.A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Nickel‐based alloys are widely used in high‐temperature applications due to their excellent mechanical strength and oxidation resistance. However, properties such as high‐temperature strength and pronounced work‐hardening make them difficult to machine.
Soheil Rooein +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source