Results 101 to 110 of about 511,940 (310)

Особенности формирования структуры зоны термического влияния в малоуглеродистой конструкционной стали при многопроходной вневакуумной электронно-лучевой наплавке [PDF]

, 2001
В работе представлены результаты исследования влияния многопроходной вневакуумной электронно-лучевой наплавки порошком стали 10Р6М5+30%WC на структуру и свойства зоны термического влияния стали 20.
Haritoglou, Christos, Hoffmann, Ulrich, Müller-Schunk, Stefanie, Ulbig, Michael W., Weber, Christian   +4 more
core   +1 more source

Characterization of a Recyclate‐Based MgO‐Steel Composite As‐Sintered Inert Anode Candidate After Exposure to Cryolite Electrolysis

Advanced Engineering Materials, EarlyView.
Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi, Alexander Adamczyk, Nora Brachhold, Gert Schmidt, Jana Hubálková, R. Gumeniuk, Alexandros Charitos, Christos G. Aneziris   +7 more
wiley   +1 more source

Effect of Weld Heat Input on Microstructure and Mechanical Properties of Dissimilar Joints of API-B and API-X42 Pipeline Steels

Journal of Advanced Materials in Engineering, 2020
In this study, the effect of welding heat input on microstructure and mechanical properties of dissimilar joints of API-X42 and API-B pipeline steels was investigated.
S. Asghari, A. M. Eslami, A. Taheri Zadeh, N. Saeidi   +3 more
doaj  

Influence of Heat Inputs on Weld Profiles and Mechanical Properties of Carbon and Stainless Steel

Nigerian Journal of Technological Development, 2021
This study examines the effect of heat input on the weld bead profile, microstructure and mechanical properties of single V- joint welded carbon and stainless-steel plates.
L. O. Osoba, W. A. Ayoola, Q. A. Adegbuji, O. A. Ajibade   +3 more
doaj  

Determination of Ranges of Components of Heat Affected Zone Including Changes of Structure / Określenie Zakresów Składowych Strefy Wpływu Ciepła Uwzględniając Zmiany Struktury

Archives of Metallurgy and Materials, 2015
A simplified analytical method to determine the range of the heat affected zone and its components during welding is presented. Heat affected zone (HAZ) is an area formed during welding in which, as the result of temperature, some structural changes in ...
Śloderbach Z., Pająk J.
doaj   +1 more source

Weldability of high-toughness iron - 12 percent-nickel alloys with reactive metal additions of titanium, aluminum, or niobium [PDF]

Three exceptionally high toughness Fe-12Ni alloys designed for cryogenic service were welded by using the gas tungsten arc welding process. Evaluation of their weldability included equivalent energy fracture toughness tests, transverse weld tensile tests
Delvetian, J. H., Stephens, J. R., Witzke, W. R.   +2 more
core   +1 more source

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Femtosecond Laser Heat Affected Zones in Aluminum

Microscopy and Microanalysis, 2022
Renae N Gannon, Thomas F Blum, Jared M Johnson   +2 more
openaire   +1 more source

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

Advanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff, Finn‐Lennard Janthur, Sascha Zimmermann, Sarah Seffer, Jörg Hermsdorf, René Gustus, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Christian Klose   +9 more
wiley   +1 more source