Results 91 to 100 of about 254,136 (312)
Advanced Engineering Materials, EarlyView.Identified through the use of statistical design of experiments and metallographic investigation, this study exposes the stochastic origins of intergranular cracks in blown powder laser beam directed energy deposition additive manufacturing of pure molybdenum. It further demonstrates a successful crack mitigation approach with direct correlation to the
Nathaniel J. Lies +2 more
wiley +1 more source
Drying characteristics and quality of red ginseng using far-infrared rays
Journal of Ginseng Research, 2015 Background: The current typical drying methods for red ginseng are sun drying and hot-air drying. The purpose of this study was to investigate drying characteristics of red ginseng by using far-infrared drying.
Xiaofeng Ning, Junsoo Lee, Chungsu Han
doaj +1 more source
Modeling and simulation of drying operation in PVC powder production line: a pneumatic dryer model [PDF]
, 2012 A one-dimensional steady-state model is developed to simulate drying of PVC powder in a pneumatic dryer. In this model, a two-phase continuum model was used to describe the steady-state flow of a dilute dispersed phase (wet PVC powder) and a continuous ...
Ansart, Renaud +4 more
core
Integrating heat recovery from milk powder spray dryer exhausts in the dairy industry [PDF]
, 2011 Heat recovery from milk powder spray dryer exhausts has proven challenging due to both economic and thermodynamic constraints. Integrating the dryer with the rest of the process (e.g.
Atkins, Martin John +2 more
core +2 more sources
Periodica Polytechnica Chemical Engineering, 2014 In this study, combined microwave vacuum drying (MVD) with hot-air drying was evaluated, and then compared with hot-air drying and freeze drying, by the quality of the created product. The aim was to show that MVD is a strong quality competitor with the conventional hot-air drying and the widely used, but expensive freeze drying.
Sándor Ferenczi +2 more
openaire +2 more sources
Advanced Engineering Materials, EarlyView.Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir +5 more
wiley +1 more source
Avaliação das propriedades nutricionais e sensoriais de snacks de castanha (Castanea sativa Mill.) [PDF]
, 2016 Aiming to increase the market offer of chestnut based products, for both increased economical return and shelf life, different preservation methods were tested on sliced chestnut.
Casal, Susana +3 more
core
Cathodic Cage Plasma Deposition of Nanostructured Cu–Fe–Se Coatings on Poly(methyl Methacrylate)
Advanced Engineering Materials, EarlyView.Nanostructured Cu–Fe–Se coatings are deposited on PMMA by a modified cathodic cage plasma process, enabling low‐temperature deposition on polymer substrates. A transition from discontinuous to compact morphology is observed with temperature, with optimal properties at 200°C, where improved CuFeSe2‐type bonding, lowest sheet resistance, and favorable ...
V. S. S. Sobrinho +8 more
wiley +1 more source
Material handling systems for the fluidized-bed combustion boiler at Rivesville, West Virginia [PDF]
, 1977 The 300,000 lbs/hr steam capacity multicell fluidized-bed boiler (MFB) utilizes complex material handling systems. The material handling systems can be divided into the following areas: (1) coal preparation; transfer and delivery, (2) limestone handling ...
Branam, J. G., Rosborough, W. W.
core +1 more source
Advanced Functional Materials, EarlyView.Intelligent radiative cooling devices, adaptable to various weather conditions, have the potential for year‐round energy savings. This study introduces a sustainable dual‐mode film made from polycaprolactone nanofibers and upcycled chip bags for effective thermal management.
Qimeng Song +4 more
wiley +1 more source