Results 161 to 170 of about 8,963,828 (215)

Multi‐Scale Mechanical Behavior of Additive‐Manufactured 316L Stainless Steel Processed by Severe Plastic Deformation

steel research international, EarlyView.
The multi‐scale mechanical behavior of additive‐manufactured 316L stainless steel processed by directed energy deposition and high‐pressure torsion is explored. The influence of torsional strain on strength and microstructural evolution is revealed, indicating progressive grain refinement in the ultrafine regime, reaching strength levels nearing 1800 ...
M. Farhan Raza, Guney Guven Yapici
wiley   +1 more source

Progress in bone tissue engineering biomaterials: Development, challenges, and prospects

VIEW, EarlyView.
Scheme 1 Application of biomaterials in immunomodulation during bone tissue engineering. Abstract Bone defect repair remains a major clinical challenge in orthopedics. Over 2 million cases caused by trauma, tumors, and other factors occur annually, with large‐scale defects posing a particular bottleneck due to limited self‐healing capacity.
Yuanbin Zhang, Junlei Chai, Quanwei Ding, Luping Liu, Kejie Zhang, Jie Lin, Jianhua Zhang, Youju Huang   +7 more
wiley   +1 more source

Multi‐omics analysis of ion channels expressed by chicken embryo vestibular type I and type II hair cells

Experimental Physiology, EarlyView.
Abstract Balance and gaze rely on the rapid and accurate detection and signalling of head movements by vestibular type I and type II hair cells. Signal transduction and transmission involve several types of ion channels, which are acquired progressively during hair cell differentiation and whose identity is known only in part.
Giulia Cheli, Roberta Giunta, Francesca Stella, Eleonora Guidi, Umberto Laforenza, Mariarosa Polimeni, Giancarlo Russo, Francesca Borgo, Lazarevic Dejan, Sergio Masetto   +9 more
wiley   +1 more source

Rat Palatability Study for Taste Assessment of Caffeine Citrate Formulation Prepared via Hot-Melt Extrusion Technology. [PDF]

AAPS PharmSciTech, 2017
Tiwari RV, Polk AN, Patil H, Ye X, Pimparade MB, Repka MA.   +5 more
europepmc   +1 more source

In Situ Generation of a Robust Gel Polymer Electrolyte From a Poly(Ethylene Carbonate)‐Hydrogenated Nitrile Butadiene Rubber Containing Thermoplastic Vulcanizate Electrolyte

Journal of Applied Polymer Science, Volume 143, Issue 41, November 5, 2026.
A gel polymer electrolyte thermoplastic vulcanizate (GPE–TPV) was prepared by blending HNBR and PEC by melt extrusion then thermally decomposing PEC to yield liquid EC. EC is absorbed into the crosslinked HNBR, yielding an electrolyte that is mechanically and electrochemically stable enough to permit cycling in a LiFePO4–Li half‐cell.
Rozita Sadeghzadeh, Gabrielle Foran, Julien Mimeault, Caroline St‐Antoine, Arnaud Prébé, Mickael Dollé   +5 more
wiley   +1 more source

Fibrillisation and Mechanical Properties of Plasma‐Treated Modification LDPE/PA6 Microfibrillar Composites

Journal of Applied Polymer Science, Volume 143, Issue 41, November 5, 2026.
Plasma treatment enhances interfacial adhesion between LDPE/PA6 via carbonyl group formation. PA6 droplet size heterogeneity reduced to ~850 nm after plasma treatment. Drawing at 160°C produces highly oriented microfibrils with faster throughput. Plasma‐treated MFCs show up to 500% tensile strength increase and 18% higher stiffness.
Narges Gray, Maximillian Pitto, Nam Kyeun Kim, Casparus Johannes Reinhard Verbeek, Simon Bickerton   +4 more
wiley   +1 more source

Design Considerations for Polymer–Deep Eutectic Solvent Hybrid Systems for Transdermal Drug Delivery

Journal of Applied Polymer Science, Volume 143, Issue 40, October 20, 2026.
Deep eutectic solvents (DESs) act as tunable, green excipients that modulate polymer structure–property relationships to enhance drug solubility, skin permeation, stability, and controlled release. Through hydrogen‐bond interactions, DES–polymer hybrid systems enable improved transdermal performance, offering a rational, design‐driven platform for ...
Madhavi Kailas Kapale, Madhur Kulkarni, Pranav J. Shah, Furqan A. Maulvi   +3 more
wiley   +1 more source

Rheology Modulation and Melt Strength Enhancement Enable Continuous Melt Spinning of PEK-C Fibers. [PDF]

Polymers (Basel)
Mao Y, Ke Z, Ma Y, Li H, Hu Z.
europepmc   +1 more source

Development of taste masked caffeine citrate formulations utilizing hot melt extrusion technology and in vitro-in vivo evaluations. [PDF]

Int J Pharm, 2015
Pimparade MB, Morott JT, Park JB, Kulkarni VI, Majumdar S, Murthy SN, Lian Z, Pinto E, Bi V, Durig T, Murthy R, Shivakumar HN, Vanaja K, Kumar PC, Repka MA.   +14 more
europepmc   +1 more source

Material Characterization of Lignin‐Filled Polypropylene Composites

Journal of Applied Polymer Science, Volume 143, Issue 40, October 20, 2026.
Ground and spray‐dried lignin powders are compared as fillers for polypropylene composites. Differences in powder preparation methods are associated with differences in powder characteristics and composite behavior after melt compounding. Spray‐dried lignin produces smaller particles and fewer large agglomerates, while a 5 wt% lignin loading provides a
Sungjun Hwang, Stefan N. E. Johansson II, Yousoo Han, Douglas J. Gardner   +3 more
wiley   +1 more source